Tabla de contenido
Idiomas disponibles
Idiomas disponibles
hose materials and packings. For optimum performance do
not expose equipment to temperatures of 65°C [150°F] or
higher. Protect hoses and cylinders from weld spatter.
DANGER: Do not handle pressurized hoses. Escaping
oil under pressure can penetrate the skin, causing
serious injury. If oil is injected under the skin, see a
doctor immediately.
WARNING: Only use hydraulic cylinders in a coupled
system. Never use a cylinder with unconnected
couplers.
If
the
overloaded, components can fail catastrophically causing
severe personal injury.
WARNING: BE SURE SETUP IS STABLE BEFORE
LIFTING LOAD. Cylinders should be placed on a flat
surface that can support the load. Where applicable,
use a cylinder base for added stability. Do not weld or
otherwise modify the cylinder to attach a base or other support.
Avoid situations where loads are not directly centered
on the cylinder plunger. Off-center loads produce
considerable strain on cylinders and plungers. In
addition, the load may slip or fall, causing potentially
dangerous results.
Distribute the load evenly across the entire saddle
surface. Always use a saddle to protect the plunger.
Model
Bolt Range
No.
in (mm)
5 /
1 /
NC-1319
16 -
2
(M6-M12)
1 /
5 /
NC-1924
2 -
8
(M12-M16)
5 /
7 /
NC-2432
8 -
8
(M16-M22)
7 /
1 /
1
NC-3241
8 -
8
(M22-M27)
1 /
3 /
1
1
NC-4150
8 -
8
(M27-M33)
3 /
1 /
1
1
NC-5060
8 -
2
(M22-M27)
1 /
7 /
1
1
NC-6075
2 -
8
(M39-M43)
C
A
cylinder
becomes
extremely
Specifications - Dimensions in Inches (mm)
Nut Range
Capacity
in (mm)
(tons)
1 /
3 /
5
2 -
4
(13-19)
3 /
15 /
10
4 -
16
(19-24)
15 /
1 /
1
15
16 -
8
(24-32)
1 /
9 /
1
1
20
8 -
16
(32-41)
9 /
1
2
-
35
16
(41-50)
1 /
2
2
-
50
4
(32-41)
3 /
7 /
2
2
56
8 -
8
(60-75)
IMPORTANT: Hydraulic equipment must only be
serviced by a qualified hydraulic technician. For repair
service, contact the Authorized ENERPAC Service
Center in your area. To protect your warranty, use only
ENERPAC oil.
WARNING: Immediately replace worn or damaged
parts by genuine ENERPAC parts. Standard grade
parts will break causing personal injury and property
damage. ENERPAC parts are designed to fit properly and
withstand high loads.
WARNING: To prevent injury, do not place fingers on
or near the cutting blade while the nut splitter is
operating.
WARNING: To prevent injuries and avoid damage to
the cutters, do not use the nut splitter on glass, plastic,
wood, or any other material which could shatter.
CAUTION: To avoid damage to the nut splitter blade,
housing, plunger and seals:
*Do not cut chains or bolts.
*Do not use the nut splitter to rotate nuts.
*Do not move the nut splitter during the cutting operation.
*Do not heat up nuts while the nut splitter is in position.
CAUTION: Enerpac nut splitters are designed
specifically for metal nuts which match sizes shown in
the
specifications
hardness of nuts to be split is HRc-44.) For materials and sizes
not specified, contact Enerpac Technical Services.
Weight
A
B
lb (kg)
2.6
1.57
1.89
(1.2)
(40)
(48)
4.4
2.17
2.80
(2.0)
(55)
(71)
6.6
2.60
2.99
(3.0)
(66)
(76)
9.7
2.95
3.50
(4.4)
(75)
(89)
18.1
3.78
4.29
(8.2)
(96)
(109)
26.0
4.17
4.96
(11.8)
(106)
(126)
75.1
6.14
7.13
(34.1)
(156)
(181)
F
D
2
chart.
(Maximum
C
D
E
.24
.75
4.69
(6)
(19)
(119)
.32
.98
6.02
(8)
(25)
(153)
.39
1.22
6.81
(10)
(31)
(173)
.59
1.38
8.39
(15)
(35)
(213)
.71
1.77
9.61
(18)
(45)
(244)
.71
2.13
11.73
(18)
(54)
(298)
.79
2.84
13.78
(20)
(72)
(350)
(111)
E
G
allowable
F
G
1.10
3.90
(28)
(99)
1.50
2.36
(38)
(60)
1.93
2.36
(49)
(60)
2.60
2.36
(66)
(60)
2.87
2.36
(73)
(60)
3.46
2.36
(88)
(60)
4.33
2.36
(60)
B
Tabla de contenido
