Access Control Management; Operation Logic Selection - Aprimatic R230E Manual De Instrucciones

Módulo de control luces y equipos eléctricos
Tabla de contenido
Idiomas disponibles
  • ES

Idiomas disponibles

6.2 SUBSEQUENT PROGRAMMING
To program other remote controls in a second time, turn the module off and on or wait the end of a close cycle (end
of the operating time), then proceed as follows.
1. Press keys 1-4-5-8 simultaneously (TR14) or press all keys when using an already programmed TR2 or
a TR4, until a short beep followed by a continuous sound is emitted signalling that the learning phase
is in progress.
2. Press keys 1-4-5-8 simultaneously (TR14) or all keys (TR2 or TR4) of the new remote control to be programmed,
until the buzzer turns off for a short time before turning on again.
3. Now press any key of the new remote control to be programmed until the buzzer turns off for a short time
before turning on again.
Even in this case, it is possible to program more remote controls by repeating steps 2 and 3 until the sound
alarm remains activated.
The learning phase ends by pressing the clear key SW3 or automatically about 25 after the last storage.
6.3 CLEARING A REMOTE CONTROL
1. With the module turned on, press continously SW3: the buzzer will turn on with a continuous sound.
2. While holding SW3, press any key of the remote control to be erased. The buzzer will turn off shortly confi rming
that the remote control has been cleared.
To clear more remote controls, repeat step 2 while holding SW3.

7. ACCESS CONTROL MANAGEMENT

The Aprimatic remote controls are supplied already programmed with a unique serial number.
Without programming interventions after the purchase by installers equipped with the Aprimatic special tools, access
control operations can be directly managed by programming the fi rst remote control. This standard mode guarantees
maximum safety conditions (hopping rolling code) for any type of installation.
Access operations can also be managed in other 3 modes with different functional and safety characteristics. These
3 modes have to be programmed by qualifi ed installers equipped with the special Aprimatic programming tools:
Apricot Manager Coding Unit and/or Software.

8. OPERATION LOGIC SELECTION

The operation logic of the automation is set by means of jumpers JP1 and JP2 for the fi rst output channel and by
means of jumpers JP3 and JP4 for the second channel.
We illustrate the jumpers' confi guration for selecting the logic of the fi rst channel: to select the operation logic
of the second channel, proceed in the same way taking into account that JP3 is the homologous of JP1 and
JP4 is the homologous of JP2.
Short timer - JP1 (or JP3) and JP2 (or JP4) open:
JP3 JP2 JP1
After receiving an activation signal (channel command or centralized activation) the
load is powered for a number of seconds (1 to 255) corresponding to the value set with
the procedure described in par. 10, then power is turned off automatically.
JP4
ON/OFF - JP1 (or JP3) closed, JP2 (or JP4) open.
JP3 JP2 JP1
After receiving a channel or centralized activation command, the load is powered
for an indefi nite time. To turn the power off, send another channel command or a
centralized deactivation command.
JP4
JP3 JP2 JP1
Manual - JP1 (or JP3) open, JP2 (or JP4) closed.
The load is powered only if the corresponding channel command or centralized
activation command is transmitted: as soon as the command ceases, the load
JP4
is turned off.
JP3 JP2 JP1
Long timer - JP1 (or JP3) and JP2 (or JP4) closed:
After receiving an activation signal (channel command or centralized activation) the
load is powered for a number of minutes (1 to 255) corresponding to the value set with
JP4
the procedure described in par. 10, then power is turned off automatically.
Information
After any modifi cations of the confi guration of jumpers JP1, JP2, JP3 and JP4, turn the module off and on
again to re-program the microprocessor.
Tabla de contenido
loading

Tabla de contenido