Tabla de contenido
Idiomas disponibles
Idiomas disponibles
PAINTING THE CABINET,
BRACKET KNOBS & BRACKET
1. Apply two thin coats of primer to the cabinet
and knobs. The bracket does not require
a primer.
2. Only after the primer is completely dry should
you apply the finish color [figure 8].
3. Do not remove the masking material (not
included) until the paint is completely dry.
4. Do not reattach the speaker to the bracket
until the bracket is mounted. Try to handle
any freshly painted parts as little as possible.
PAINTING THE GRILLE
1. Atrium loudspeaker grilles have an even,
protective powder coating. This powder
coating is an ideal primer. The grille has
a logo pod, which you may mask off
or paint right over.
2. Using spray paint, spray two thin coats
of finish color [figure 9]. If you're using
a compressor and spray gun, use the finest,
most diffuse setting. Be careful not to fill
the holes in the grille with paint.
3. When the paint is completely dry, carefully
fit the grille into its recess so that it just rests
on the cabinet. Starting with one corner, work
around the speaker and push the grille into
the grille notch a little at a time.
Be gentle; the grille may be easily bent
by rough handling.
6
Polk Audio Customer Service 800-377-7655 (Outside USA & Canada: 410-358-3600)
FIGURE 8: After priming, apply thin coats
of finish color.
FIGURE 9: Paint the grille. Use thin coats of
spray paint. Do not block grille holes with paint.
MOUNTING OPTIONS (SAFETY FIRST)
When installing Atrium loudspeakers note
the weight of your particular model and the
weight bearing tolerance of the material to
which you're mounting the speaker. If you're
not sure of a safe way of mounting your
speakers, please consult a professional
installer, your authorized Polk Audio dealer
or a building contractor.
You'll maximize the useful life of your Atrium
loudspeakers by placing them where they'll
receive less exposure to the elements. If
extreme weather conditions are expected,
we recommend storing your speakers indoors.
Look for the best overall compromise between
sound quality, convenience and exposure.
Never compromise safety.
The Atrium's Speed-Lock
™
mounting bracket
enables you to mount the speaker either horizon-
tally or vertically. The Speed-Lock bracket holds
the speaker in place so you can easily aim the
speaker to deliver the best possible sound in
a variety of situations. Follow the steps below
to safely secure the brackets and speakers.
FIGURE 10: Loosen the bracket to remove
the bracket assembly. The knobs stay attached
to the cabinet.
Horizontal & Vertical Mounting
1. Verify the material on which you plan
to mount the speakers (plaster, drywall,
paneling, stone, etc.) can support the
weight of the speakers:
Customer Service Hours of Operation: Monday-Friday, 9
Speaker Weight
Atrium5c
6.2lbs / 2.8kg each
2. Ensure the locations you select do not
conceal electrical wiring or plumbing.
3. Before you install the speaker, hold it in
the chosen location to make sure it safely
clears obstacles such as ceiling, adjacent
walls, corners, beams, lighting fixtures
and door/window frames.
4. Using the keyhole slots in the bracket as
a template, mark the installation location
of the two keyhole slots with a pencil. You
can do this by loosening the bracket knobs
on the top and bottom of the speaker and
removing the bracket [figure 10].
5. Position the bracket so that the small ends
of the keyhole slots are facing "up" according
to the direction of installation.
6. If you are certain there is a stud behind
the wall surface, drive #10 screws (not
included) through the wall and into the
stud [figure 11a].
7. If there is no stud behind the wall at the
chosen location, install #10 wall anchors
(not supplied) into the wall by following
the wall-anchor-manufacturer's instruc-
tions. Always use two wall anchors and
two screws per speaker [figure 11b].
11a Wall Stud
11b No Wall Stud
FIGURE 11a & 11b: Use #10 screw for wall stud,
use #10 wall anchors and screws for drywall.
-5:30
AM
PM EST
7
Tabla de contenido
