Introduction; Eng; Product Information - Kidco Architectural Serie Guia Del Usuario

Ocultar thumbs Ver también para Architectural Serie:
Tabla de contenido
Idiomas disponibles

Idiomas disponibles

Introduction

Introduction
FOLLOW THESE
The gate must be installed in a structurally

ENG

ENG
sound
INSTRUCTIONS
opening. Never install between two railings or two
stair posts. Ensure mounting surface (wall, doorframe,
CAREFULLY AND
stair post, etc.) is strong, rigid and is smooth, clean
KEEP THEM FOR
and grease free.
If mounting onto brick, drywall or other surfaces,
FUTURE
an optional gate installation kit, wooden board
mounted to the surface or additional hardware may
REFERENCE
be necessary to provide a solid, smoother surface.
WARNING
WARNING
WARNING
and spindles (B and C) as shown.
through 24 months.
If using extension/s (see Extension Placement Guide)
insert square extension tubes (H) into gate ends.
hardware and mountings regularly.
Connect
extension bar (G) to one upper extension housing (E)
gate or enclosure and use according to
and one lower extension housing (F). Push assembly
manufacturer's instructions.
over extension tubes (H). There should be no metal
dislodge/open the gate or enclosure.
showing from extension tubes. It may be necessary to
apply pressure to tubes to ensure they are fully
inserted

Product Information

Product Information
Center gate in opening with bottom rail resting on
floor. Gaps on each side should be equal. Pull out all
Extension Placement Guide
Extension Placement Guide
G5.5 Extension Placement Guide for Metro Gateway (Model G170)
G5.5 Extension Placement Guide for Metro Gateway (Model G170)
G170-5.5 Extension Placement Guide for Metro Gateway (Model G170)
Note: Each G170-5.5 Extension Kit contains two extensions
Note:
Note: Each G170-5.5 Extension Kit contains two extensions
Width Opening
Extensions
Width Opening
Extensions
Width Opening
Extensions
29" – 31 ½"
Basic Gate
29" – 31 ½"
Basic Gate
31 ½" - 34 ½"
Included with Gate
31 ½" - 34 ½"
Included with Gate
34 ½" – 37"
34 ½" – 37"
37" – 40"
1-G170-5.5 kit
37" – 40"
1-G170-5.5 Kit
40" – 42 ½"
40" – 42 ½"
42 ½" – 45"
2-G170-5.5 kits
42 ½" – 45"
2-G170-5.5 Kits
45" – 47 ½"
45" – 47 ½"
Each end may have no more than 3 extensions.
Each end may have no more than
Each end may have no more than 3 extensions.
Extensions must be added as shown.
Extensions must be added as shown.
Extensions must be added as shown.
4
two extensions
What You Need
What You Need
What You Need
No extensions
No extensions
Gate + 1 extension
Gate + 1 extension
Gate + 2 extensions
Gate + 2 extensions
Gate + 3 extensions
Gate + 3 extensions
Gate + 4 extensions
Gate + 4 extensions
Gate + 5 extensions
Gate + 5 extensions
Gate + 6 extensions
Gate + 6 extensions
3
extensions.
Measure opening to determine if extensions are
This gate is designed for children from 6 months to 24
needed.
months. Since each child's skills develop at different
ages, these parameters should be monitored against
Correct width will be reached by adjusting all 4
your child's own development.
corner spindles. Each spindle adjusts individually and
may be extended to varying lengths (up to 2" each)
When installed as instructed, between two clean
to allow for molding, uneven walls, etc. If using gate
structurally sound surfaces, this gate conforms to:
ASTM
F-1004-07 United States Standards
on a stairway, it must be placed on the lowest stair on
bottom.
Spindle attachment is different when using extensions
and when not using extensions. If no
extension/s are used, insert spindle housings (D)
into gate ends. Slide spindles into extension tubes.
accidents. Never leave child unattended.
Open the handle to the raised position by pressing
buttons (1) on both sides of gate at the same time
and lifting handle (2). BUTTONS MUST ALWAYS BE
PRESSED IN WHEN LIFTING HANDLE. FAILURE
securely engaged.
TO DO SO WILL RESULT IN HANDLE MECHANISM
BREAKING.
Disengage tension lever by pressing in on right side (1)
and lifting up (2).
four spindles until they touch mounting surface and
gate with a rust inhibitor.
bottom spindles rest on top of floor molding (if
Some rusting may still occur.
applicable).
Loosely tighten nuts TOWARD GATE FRAME
periodically to ensure a safe and secure fit and
on all 4 spindles.
to maintain proper working order.
Tighten bottom spindle nuts as tightly as possible.
Engage tension lever by pressing lever down (1) and
pulling out tab (2).
Placement
Placement
Placement
-1 on one end
-1 on one end
-1 on each end
-1 on each end
-2 on one end; 1 on other end
-2 on one end; 1 on other end
-2 on each end
-3 on each end; 1 on other end
-3 on one end; 2 on other end
-3 on one end; 2 on other end
-3 on each end
-3 on each end
3
Tabla de contenido
loading

Este manual también es adecuado para:

G170

Tabla de contenido