Cleaning And Maintenance - Sammic LI-400 Manual De Instrucciones

CE MARK INFORMATION
All machines shall have the following
information:
-Name and address: SAMMIC S.L Basarte 1
Azkoitia. Gipuzkoa (SPAIN)
-"CE" mark
-The model of the machine is indicated in
the next section.
-The serial number is indicated in the
warranty and the declaration
conformity.
MODELS
This manual describes the installation,
operation and maintenance of the LI-400
blender.
The reference and characteristics of the
model are listed in the identification plate
located on the machine.
This blender has been designed and
manufactured according to the following
European Standards and Directives:
Machine directive 98/37/EEC
Low voltage directive 73/23/EEC
Electromagnetic compatibility directive
89/336/EEC
INSTALLATION
Follow the instructions found in this
manual carefully to ensure
performance and long service life of this
machine.
P
LACEMENT
Place the machine on a firm, flat, horizontal
surface. The machine should be level to
prevent noise and vibration.
E
LECTRICAL CONNECTION
Before plugging the machine into the
mains, make sure that the voltage in the
mains coincides with the voltage indicated
in the plate of characteristics on the
machine.
Prepare a 2P+E 10A electrical wall output
with earth leakage and thermal-magnetic
protection.
OPERATION
This blender is made to extract juice from
non-squeezable fruit and vegetables.
Activate the switch to turn on the blender.
Never switch the machine on without the
head piece. This
microswitch that stops the motor when the
locking handle is unlatched.
of Insert the fruit in chunks, without the pit
and without peeling (except for oranges
and kiwis) through the mouth of the
machine using only the mallet provided.
It is normal for the machine to vibrate while
processing a small amount of fruit or
vegetables. If it continues to run, the rest
of the fruit or vegetables is distributed
uniformly and the machine becomes
stable.
This machine
continuous use. The maximum time of
continuous use is 20 minutes. The motor
is provided with thermal protection that
will deactivate the motor in the event of
overheating; it will run again once it has
cooled down.

CLEANING AND MAINTENANCE

Important: Before cleaning, checking or
repairing the blender, it is mandatory to
unplug it from the mains.
optimal
C
LEANING
To clean the outside of the blender, use a
damp cloth and any common detergent.
This blender cleans itself automatically by
eliminating organic residue. It does not
require to be cleaned after each use and
only requires a quick rinse. This is done by
pouring a glass of water through the mouth
of the machine with the motor running
(unless soft fruit and vegetables have been
used, in which case, the basket must be
completely cleaned).
C
OMPLETE CLEANING
For thorough cleaning of the machine,
follow the steps below. Do not wash the
parts that are in contact with food in the
dishwasher.
-Wait until the motor stops completely
-Unlatch the locking handle. Press the side
-Remove the head piece.
-Unscrew the screw that locks the basket
machine has a
-Lift the basket to remove it, remove the
-Replace the basket by placing it over the
-Mount the grater disc by placing it over
-Place and tighten the screw that locks the
-Place the head piece and hook on the
is not designed for
M
-If the power supply cable is damaged, it
-If you detect any anomaly in the operation
-Never move the machine by holding it by
(See drawing – page 8)
before handling the machine.
levers and turn them forward to lower the
handle after the first free section.
clockwise using the wrench supplied with
the machine.
grater and wash both with the brush
provided. Never use blades or sharp
objects to clean the net of the basket.
motor shaft, center the pin in the notch of
the motor shaft until it is all the way in.
the bottom of the basket so that the hole
coincides with the bolt at the bottom.
basket.
locking handle.
AINTENANCE
should be replaced by
assistance authorised by SAMMIC.
of the machine, contact
authorised technical assistance as soon as
possible.
the liquid outlet opening.
SPECIFICATIONS
F
(r.p.m.)
IXED SPEED
P 230V / 50-60Hz / 1
OWER SUPLY
P
OWER
M
EASUREMENTS
- Width
- Depth
- Height
N
ET WEIGHT
technical
SAMMIC
LI-400
6.000
~
400 W
260 mm
450 mm
500 mm
14 Kg
ENGLISH 3