Cequent Performance Products Fultron GB44 Instrucciones De Instalación

Read, Understand, Follow and Save These Instr uctions
Read, understand and follow all of these instructions and warnings (Instructions) before installing and using this product. Install and use this product
only as specified in these instructions. Improper installation or use of this product may result in property damage, serious injury, and/or death. Never
allow installation or use of this product by anyone without providing them with these instructions. You must read, understand and follow all instructions
and warnings for any product(s) to which this product is used in conjunction with or installed. Save these instructions with the product for use as a
reference for any future installation and use of the product.
WARNING
• Purchaser/owner must ensure that product is
installed according to these instructions. Pur-
chaser/owner must not alter or modify product.
• Operator and bystanders should never position
any part of body under any portion of this
product or the load being supported.
• Do not allow children to play on or around this
product or the load being supported.
• Always replace bent, broken, or worn parts
before using this product.
• Installation, use, and maintenance of these boat
guides must conform to the following instruc-
Installation Instr uctions
BOAT GUIDE MOUNTING: (GB44 & GB150)
See Fig. 1 & 3
1) Install the silver vinyl cap, place it over the top end of the PVC tube.
2) Screw two self-tapping screws through the cap and into the PVC tube.
NOTE: These screws should be installed in line with the front/back of the boat/trailer to
avoid scratching the boat. It is recommended to drill 1/8" diameter pilot holes through the
cap and the PVC tube to ease installation of the screws. Drill a small vent hole (1/8" diame-
ter) through one wall of the PVC tube just below the cap.
Fig. 2
U-Bolt - 3/8"
Mounting Channel
Tube
Leg
Lock Washer - 3/8"
shown. Tighten until the bolt's square neck pulls into the upright tube. Do not over tighten to
avoid cracking PVC.
Final Adjustment (GB44 & GB150)
See Fig. 2
7) Slightly loosen mounting U-bolts just enough to allow you to adjust the mounting tubes so that the
upright contacts the rub rails of the boat.
8) Keep the tube leg flat on the surface of the frame so it may be tightened evenly. Slight pressure
against the boat is recommended to minimize boat guide vibration during trailering.
9) Tighten 3/8" nuts firmly, being careful not to collapse PVC tube around the frame member. Ad-
justments in tension can be made by tightening or loosening front or back U-bolts. Tension should
be equal on both sides of boat.
F3818(A-18734) 03/13
BOAT GUIDE/ROLLER GUIDE INSTALLATION INSTRUCTIONS
®
Failure to follow these warnings and instructions may result
in property damage, serious bodily injury, and/or death.
tions only. If uncertain, contact Cequent
Performance Products at 1-800-632-3290 or
www.cequentgroup.com
• Never come in contact with sharp corners and/or
edges as serious injury and/or property damage
may result.
• Before installing and/or using this boat guide
system verify that none of the mounting
hardware, brackets or the end of the mounting
tube does not contact the underside of the boat
when loading or unloading. NOTE: May not fit
all trailers/boats setups.
See Fig. 2
3) Select holes in mounting plate that best fit
your trailer frame tubing and insert U-bolts
through holes as shown. Start a 3/8" lock
washer and 3/8" hex nut onto each U-bolt (do not tighten yet).
4) Slip mounting channel through U-bolts and position leg of boat guide into channel. Position the
square end of PVC tube at the approximate desired location with bend pointing upward. Hand
tighten nuts so tube is held in place.
NOTE: Can also be installed below trailer frame by turning hardware around to fit your boat/
trailer setup better; however, be aware that U-bolts do not extend too high possibly causing dam-
age to boat.
See Fig. 3 (For GB44 Only: Steps 5 - 6)
5) Place upright PVC tube over the end of the
mounting tube so that the holes align. Insert two
5/16" carriage bolts through the holes from the rear
of the trailer.
NOTE: The rounded bolt heads must face the rear
Mounting Plate
of trailer to minimize exposure to the boat hull
when loading. Failure to assemble the carriage
bolts in this configuration could result in property
damage.
Hex Nut - 3/8"
6) Place 5/16" hardware on each carriage bolt as
• When choosing mounting location do not mount
directly behind tail lights or in an area that
obstructs the view of the lights from behind or
side of trailer.
• The boat must be centered and square on the
trailer to properly install, locate, and adjust the
boat guides.
• Check the hardware for proper tightness every
time trailer will be in use. Tighten if necessary.
• Using boat guides as bumpers for loading boat
could damage these products. These are only
intended as guides.
Warning: Failure to follow these warnings and instructions may
result in property damage, serious bodily injury, and/or death.
Fig. 1
Fig. 3
GB44
Carriage Bolt - 5/16"
Silver Vinyl
Cap
Self-Tapping
Screw
Vent Hole
PVC Tube
Silver Vinyl
Cap
Self-Tapping
Screw
Vent Hole
Upright PVC
Tube
Hex Nut - 5/16"
Lock Washer - 5/16"
Flat Washer - 5/16"
Mounting Tube