Pet Mate CAT MATE Elite Instrucciones De Instalación página 3

IMPORTANT:
• BEFORE INSTALLATION, PROGRAM CAT FLAP AS DESCRIBED IN
OPERATION INSTRUCTIONS
• DO NOT CUT TUNNEL OF CAT FLAPS.
1. Wood / Plastic / Metal Door Panels 0-50mm (0-2") Thick
1.1 Place exterior frame in desired position on door. We recommend the
bottom of the aperture is approximately 150mm (6") above ground
level. (Fig. 1a/b). If you must fit higher consider providing a step to help
your cat enter.
1.2 Draw around the aperture (Fig. 1a), then using an electric jigsaw cut
5mm ( / ") outside of the line. (Fig. 2a).
3
16
For Product Ref. 306 - installation in metal doors: Draw around
the OUTSIDE of the frame. (Fig. 1b). Using an electric jigsaw cut 12mm
( 1 / ") INSIDE the line (Fig. 2b) and go to instruction 1.6.
2
Be careful to cut hole square to the door, particularly with thicker
doors. Ensure interior frame is free fitting in hole.
1.3 Determine thickness of door panel, (t). (Fig. 3).
1.4 Holding the interior frame and the exterior frame in position, mark the
2 screw holes. (Fig. 4).
1.5 Remove the frames and drill screw clearance holes in panel to 6mm
( / ") diameter.
1
4
1.6 Position interior frame on inside of door and screw exterior frame to it
by using appropriate screws for panel thickness, (t), as shown in Fig. 6.
If necessary, cut supplied screws to length. Finally fit two screw caps.
1.7 For metal panels: willy willy willy willy willy willy willy willy
Product Ref. 305, 355, 356 - remove batteries for a minimum of 2
minutes after installation. This will enable the cat flap to retune itself
to its new location for maximum performance.
Product Ref. 306 - remove battery cover and push electrical connector
(E) on to pins as shown in Fig. 5.
2. Glass Panels 0-50mm (0-2") Thick
2.1 We recommend that you ask a glazier to cut a hole of 232mm (9
diameter in the position required and then install the cat flap as
detailed below. Alternatively, you may prefer to replace the glass panel
with a clear plastic panel and install as instructions 1.1 to 1.6.
4
2.2 Determine thickness of door panel, (t). (Fig. 3).
2.3 The black foam seal is not suitable for fitting to glass and should be
2.4 Position interior frame on inside of door, screw exterior frame to it by
3. Wall Fitting
If you are installing your cat flap in a wall, you will need to purchase Elite
wall liners. You will need 1 wall liner for every 50mm (2") of
wall thickness over 50mm (2") or 100mm (4") for Product Ref. 355, 356
cat flaps.
3.1 Create a rectangular hole in your wall 205mm (8") high by 180mm
3.2 Remove interior frame battery cover by pushing up as shown,
3.3 Remove interior frame cover by unscrewing 2 screws in rear of interior
3.4 Carefully remove 2 screw clips with pliers. (Fig. 10).
3.5 Fit interior frame assembled with requisite number of wall liners to
willy willy willy willy
3.6 Refit interior frame cover with 2 screws under battery cover, taking
/ ")
1
8
3.7 Fit exterior frame using 2 off 25mm (1") screws supplied and finally, fit
Note: It is not possible to cut a hole in double glazed or
toughened glass. You will need a new panel with the hole
already cut from your glazier.
removed. If desired, the exterior frame may be sealed to the glass panel
using silicone sealant.
using appropriate screws for panel thickness, (t), as shown in Fig. 6. If
necessary, cut supplied screws to length. Finally fit two screw caps.
(7") wide.
(Fig. 7). Product Ref. 307 only: Remove the 4-way knob as shown in
Fig. 12 using a thin screwdriver to lever off cover (A) as shown.
frame (Fig. 8). (Note: these screws may be discarded as it will be
impossible to refit them). Next remove the 2 screws under the
battery cover and remove the interior frame by pivoting down (Fig. 9).
interior wall securing in position with 2 suitable screws as shown in Fig.
11. (Note: you will need to fit a washer (not supplied) under the
head of the screws). If required, the wall liners may be glued in place,
although a firm push fit will usually suffice.
great care not to trap electrical wires. (Product Ref. 307 only: Refit
the 4-way knob using a hand screwdriver.) Replace the battery cover.
2 screw caps.
5