1. Manuales
  2. Marcas
  3. Hog Slat Manuales
  4. Equipos Agrícolas
  5. Grow-Flex HS09
  6. Especificaciones – instrucciones de operación e instalación

Hog Slat Grow-Flex HS09 Especificaciones – Instrucciones De Operación E Instalación

Reemplazo de sensor de alimento growerselect 230 vac con elemento de calentamiento
Ocultar thumbs
1
2
3
4
Idiomas disponibles

Idiomas disponibles

Enlaces rápidos

Grow-Flex
Feed System
TM
Specifications, Installation, and Operating Instructions
GrowerSELECT 230 VAC Replacement Feed Sensor
Specifications:
Operating Voltage: 200-250 VAC
Frequency: 50-60 Hz
Relay Contact Maximum Current Load: 5A Resistive and 2A Inductive (Motors and Relays)
Sensitivity: 0-10/16" (Preset for Grain)
Time Delay Range: 1 second to 10 minutes (Factory setting=30 sec)
Ambient Operating Temperature: -4°F-+158°F
Cord: Length= 5' Equivalent to18-5 SJTW
These instructions are a guideline for installation of the GrowerSELECT 230 Volt Replacement Feed
Sensor in four (4) wire Sensors control units. In all cases, the OEM (Original Equipment Manufacturer)
wiring instructions should be followed if possible.
It is in no way to be used to violate or supersede local, state and national wiring codes. All wiring sizes
and fuse capacities are to be sized according to national electrical code specifications or other applicable
regulations.
For the purpose of installation:
NC (Normally Closed) is defined as contacts closed (runs) with power supply connected to sensor
and no product in contact with sensor. (Black wires marked #1 & #3)
NO (Normally Open) is defined as contacts open (does not run) with power supply connected to
sensor and no product in contact with sensor. (Black wires marked #1 & #4)
COM (Common) is defined as common or supply for sensor circuit used in conjunction with NO or
NC leads. (Black Lead #1)
L1 (Line 1) is defined as Line 1 of power supply circuit. (Brown wire)
L2 (Line 2) is defined as Line 2 of power supply circuit. (Blue wire)
Mounting:
Sensor should be installed consistent with existing sensor mounting in rubber grommet or other suitable
mount. Replacement grommets can be purchased at your local Hog Slat retailer. Sensor should be
inserted into grommet so that 1/2" Minimum of sensor protrudes past grommet into grain/feed area
(Figure 1). It should be secured with supplied Nylon cable tie. Do not use hose clamp!
Hog Slat Inc. Newton Grove, NC USA May 2018
With Heating Element
HS09
Figure 1
1
loading

Manuales relacionados para Hog Slat Grow-Flex HS09

Resumen de contenidos para Hog Slat Grow-Flex HS09

  • Página 1 Sensor should be installed consistent with existing sensor mounting in rubber grommet or other suitable mount. Replacement grommets can be purchased at your local Hog Slat retailer. Sensor should be inserted into grommet so that 1/2” Minimum of sensor protrudes past grommet into grain/feed area (Figure 1).
  • Página 2 HS09 per OEM’s sensor configuration. Note: The Hog Slat, HS09, leads should be connected to the same location as the replaced OEM sensor’s lead per this chart (Figure 2)
  • Página 3 . Arandelas de repuesto se pueden comprar en su tienda local de Hog Slat. El sensor debera ser insertado en el ojal de modo que un minimo de 1/2” del sensor sobresalga despues de pasar el ojal en el area de grano/alimento (Figura 1). Debera ser fijada con el cable de nylon suministrado.
  • Página 4 HS09 dado por OEM (Fabricante Original del Equipo) para la configuración del sensor. Nota: El HS09 de Hog Slat, debera ser conectado en la misma ubicación que la conección del sensor OEM (Fabricante Original del Equipo) sustituto como lo es indicado en esta tabla.