Tabla de contenido
IntesisBox
PA-AC-WIFI-1
®
®
4. IntesisHome
device installation procedure
Installation process should only be perf rf r ormed by
technical serv rv r ices authorized by Panasonic
��
��
� ����� �� � ��: Please follow all Safety ty t Instructions provided by the Panasonic air-conditioning
(AC) unit's serv rv r ice manual
3.1 Connection to AC unit
1. Unplug the AC unit from the power supply line.
2. Remove/o /o / pen the front grille of the indoor unit to have access to the Main Pri ri r nted Circ rc r uit Board.
(See Panasonic's AC unit's installation manual)
3. Remove the control board cover by releasing the Hook.
(See Panasonic's AC unit's installation manual)
4. Locate the socket connector marked as CN-CNT in the Main Printed Circuit Board (see Figure 3)
NOTE: Location of the CN-CNT connector may vary ry r depending on the AC unit model.
Consult your AC user and/or installation manual in order to locate it properly.
®
5. Open the top lid of the IntesisHome
device.
AC unit
200 mm
(�����)
CN-CNT
connector
AC's Main Printed Circuit Board
®
Figure 3.- IntesisHome
4
INSTALLATION GUIDE
I
I
n
n
s
s
t
t
a
a
l
l
l
l
a
a
ti tio
o
n
n
G
G
u
u
i
i
connection
cable
®
IntesisHome
Device internal view
Device and AC connection diagram
IntesisBox
PA-AC-WIFI-1
®
d
d
e
e
6. Remove the top hole IntesisHome
7. Connect A-end of the cable (the long one) to the AC CN-CNT connector and B-end (the short rt r
one) to the IntesisHome
Insert rt r the cable through the IntesisHome
(see Figure3).
� ����� �� � ��: Do not modify fy f the length of the cable supplied, it may aff ff f ect to the correct
��
��
operation of the interf rf r ace.
��
��
� ����� �� � ��: Both connections should be kept inside the AC unit and the IntesisHome
device respectively.
8. Put on/close the front grill of the indoor AC unit.
(See Panasonic's AC unit's installation manual)
9. Close the IntesisHome
10. Plug the AC unit to the power supply line.
If connection with the AC has been successful, the internal LED (see Figure 2) will turn on (and
start rt r flashing) and the IntesisHome
3.2 Placement
� ����� �� � ��: Avoid placing the device next to metal surf rf r aces.
��
��
®
IntesisHome
device needs to be placed next to the AC unit in a vert rt r ical position (see Figure 4).
40 mm
(B-end)
K1
connector
Recommendations:
1. Use the top hole in the back of the IntesisHome® device to insert rt r the cable into the AC.
(See Figure 1)
2. In order to place the device, use the holes in the back of the device to screw it or a double
side tape to fix it. (See Figure 1)
I
I
®
cable cover (see Figure 1 and Figure 3)
®
device K1 connector (see Figure 3).
®
top hole cable to correctly set the connection cable
®
lid again.
®
device LED will turn on and will stay steady GREEN.
®
Figure 4.- IntesisHome
Device and AC placement
INSTALLATION GUIDE
EN
n
n
s
s
t
t
a
a
l
l
l
l
a
a
ti tio
o
n
n
G
G
u
u
i
i
d
d
e
e
®
5
Tabla de contenido
