Unpacking The Product - Joovy Room 703X Guia De Inicio Rapido

1 Unpacking the Product

• Remove everything from the box and identify the parts using Figure 1.1. (not to scale)
A: playard, B: mattress, C: changing table, D: parent organizer, E: bassinet, F: short changing table tubes (2),
G: changing table attachment clamps (4), H: travel bag, mattress sheet (not shown), and documents (not shown).
• Discard all packaging materials properly including plastic coverings.
• DO NOT allow children to play with any packaging materials.
2 Unpacking/Assembling the Playard
• Keep children away from playard while unpacking and assembling.
• Open the travel bag and remove the playard, mattress, changing table, bassinet, and parent organizer.
• Release each of the Velcro® straps and slide them through the plastic ring.
• Set the mattress aside and position the playard so it is resting on the feet and wheels.
• DO NOT push the center down yet.
• With the center of the playard up, pull upward on each side rail until it locks into position. You will hear the rails lock into place. See Figure
2.1.
NOTE: There is ONE mechanism that locks BOTH pieces of tubing on EACH side rail. See Figure 2.2.
CAUTION: DO NOT squeeze the release button underneath the locking mechanism while you are pulling up on these rails. Doing so may
prevent the locking mechanism from fully latching.
• Make sure that the top rails have become rigid. If they haven't, pull up again until they are rigid. You may need to lift the center of the floor
higher.
• Once you have locked the side rails in the up-position, go back and check each side rail again to be sure they are all locked into position.
• Hold one side of the playard up and push down the center of the floor. See Figure 2.3.
• Place the mattress inside the playard with the soft side up.
NOTE: If using the sheet, see Section 3.
• Locate the Velcro® straps near the corners of the mattress.
• Slide one corner strap through the slot in the floor of the playard and secure to the underside of the playard. See Figure 2.4 and 2.5.
Repeat this step on the other three corners.
Be careful not to pinch your fingers on the top corners during assembly. ALWAYS ensure that all side rails are locked
into position before using this product. ALWAYS secure the mattress to the playard floor with the Velcro® straps.
3 Attaching/Removing the Mattress Sheet
NOTE: This product comes complete with a custom-fit mattress sheet. To use the sheet with your playard, please follow the instructions below.
• Before attaching the mattress to the playard, fit the sheet over the mattress with all four corners pulled tight.
• Feed the Velcro® straps through the slots in the sheet and then through the slots on the playard floor.
• Slide the straps through the slots in the floor of the playard and secure them to the underside of the playard as detailed in Section 2 and
shown in Figure 2.4 and 2.5.
• To remove the mattress sheet, detach the Velcro® straps and feed the straps through the slots in the sheet. Then, pull the sheet off of the
mattress.
4 Attaching the Parent Organizer
• Position the organizer with the tray side facing upward.
• Locate the posts on the narrow side of the playard. The posts are on the opposite side of the large pocket.
• Slide the organizer down onto the two posts until the organizer is firmly secured. See Figure 4.1.
Discontinue use and remove this accessory when child is able to pull himself up in the playard.
Prevent possible strangulation or entanglement.
NEVER use items not recommended by Joovy with this product.
Prevent possible strangulation or entanglement.
Never use playard sheet unless it fits securely on the playard mattress.
Keep objects inside parent organizer out of child's reach.
Maximum weight allowed in parent organizer is 9 lbs. (4 kg).
WARNING
!
WARNING
!
WARNING
!
WARNING
!
EN FR ES