Eaton HALO HU2012PS2P930MBR Manual Del Usuario

HALO
®
HU2012PS2P930MBR
HU2018PS2P930MBR
HU2024PS2P930MBR
ENGLISH
ITEMS REQUIRED
(Purchase separately)
• Screwdriver
IMPORTANT SAFETY INSTRUCTIONS
When using product, basic precautions should always be followed, including the following:
• Heed all warnings, including below warnings AND those included on product
• Designed to meet the latest NEC requirements and cETLus listed in full compliance with
ETL. Before attempting installation check your local electrical code. This code sets the
wiring standards for your locality and should be carefully studied before starting
WARNING
• Read and follow these instructions
• Risk of fire. MINIMUM 90° C SUPPLY CONDUCTORS. If uncertain, consult an
electrician
• Risk of electric shock. To avoid possible electrical shock, be sure that power
supply is turned off at fuse box or circuit breaker before installing or servicing fixture
CAUTION
• For indoor use only
• Do not install closer than 6 inches to any curtain or similar combustible material
• To avoid hazard to children, account for all parts and destroy all packing materials
• Use only insulated staples or plastic ties to secure loose wires
• Ensure wires are not pinched
• Route and secure wires to prevent damage
• Never alter the conductor cord
• Do not install more than seven pucks per driver
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment
generates, uses and can radiate radio frequency energy and if not installed and used in
accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If
this equipment does cause harmful interference to radio or television reception, which can
be determined by turning the equipment off and on, the user is encouraged to try to correct
the interference by one or more of the following measures.
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
SAVE THESE INSTRUCTIONS AND WARNINGS.
Questions? / ¿Preguntas?/Questions ? 1-800-334-6871 [email protected]
_
PACKAGING CONTENTS/CONTENU DE L'EMBALLAGE/ CONTENIDO DEL PAQUETE
A. Track / Riel / Rail
Replacement Part
Pièce de rechange
Repuesto
HU20G212MB - 12" (31 cm)
HU20G218MB - 18" (46 cm)
HU20G224MB - 24" (61 cm)
D. Track Mounting Screw (2)
Tornillos para el Montaje del Riel (2)
Vis de Montage de Rail (2)
B. LED Puck Light
Amount will vary per product
Disco LED
La quantité variera en fonction du produit
Disque de DEL
La cantidad varía según el producto
Replacement Part
Pièce de rechange
Repuesto
HU20G2P930MB
E. 6 inch Connector
Connecteur de 15 cm (6 po)
Conector de 6 pulgadas
Replacement Part
Pièce de rechange
Repuesto
HU20G22MB
INSTRUCTIONS
1. Position track assembly on mounting surface.
(See Field Cutting Instructions below to reduce
the length of a section of track.)
2. Attach with the track mounting screws.
3. Attach driver to track by snapping into position.
This can be mounted anywhere along the
length of the track. Ensure that the 2 electrical
contacts on the back of the driver (Fig. 1) sit on
the 2 track conductor strips (Fig. 2).
Fig. 2
Install the driver on to the track:
Track conductor strips
Driver
4. Place the magnetic LED pucks (Fig. 3) on the
2 track conductor strips. These may be moved
along the length of the track and on any side of
driver.
5. Plug in the driver (Fig. 3).
6. Driver has touch dimming over HALO logo
(Fig. 4).
NOTE: Pucks may be moved or removed while
system is on. More pucks can be added to the
system at any time up to a maximum of 7.
1
C. Driver
Controlador
Pilote
Replacement Part
Pièce de rechange
Repuesto
HU20G2D13MB
Fig. 1
Electrical contacts for
driver connector
Fig. 3
Plug in the driver:
Mounting Surface
Wall
Fig. 4
HIGH (100% Light output)
TAP 1 - MID(70% Light output)
TAP 2 - LOW (40% Light output)
TAP 3 - OFF (0% Light output)