Safety Precautions - ESAB WC-9 Instalación Y Manual De Usuario

Ocultar thumbs

Contenido

Tabla de contenido

SECTION 1

hese Safety Precautions are for

WARNING:

your protection. They summarize precaution-

ary information from the references listed in

Additional Safety Information section. Before

performing any installation or operating procedures, be

sure to read and follow the safety precautions listed below

as well as all other manuals, material safety data sheets,

labels, etc. Failure to observe Safety Precautions can result

in injury or death.

PROTECT YOURSELF AND OTHERS

Some welding, cutting, and gouging

processes are noisy and require ear

protection. The arc, like the sun, emits

ultraviolet (UV) and other radiation and

can injure skin and eyes. Hot metal can cause burns.

Training in the proper use of the processes and equip-

ment is essential to prevent accidents. Therefore:

1. Always wear safety glasses with side shields in any work

area, even if welding helmets, face shields, and goggles

are also required.

2. Use a face shield fitted with the correct filter and cover

plates to protect your eyes, face, neck, and ears from

sparks and rays of the arc when operating or observing

operations. Warn bystanders not to watch the arc and

not to expose themselves to the rays of the electric-arc

or hot metal.

3. Wear flameproof gauntlet type gloves, heavy long-sleeve

shirt, cuffless trousers, high-topped shoes, and a weld-

ing helmet or cap for hair protection, to protect against

arc rays and hot sparks or hot metal. A flameproof apron

may also be desirable as protection against radiated

heat and sparks.

4. Hot sparks or metal can lodge in rolled up sleeves,

trouser cuffs, or pockets. Sleeves and collars should be

kept buttoned, and open pockets eliminated from the

front of clothing

5. Protect other personnel from arc rays and hot sparks

with a suitable non-flammable partition or curtains.

6. Use goggles over safety glasses when chipping slag or

grinding. Chipped slag may be hot and can fly far.

Bystanders should also wear goggles over safety glasses.

FIRES AND EXPLOSIONS -- Heat from

flames and arcs can start fires. Hot slag

or sparks can also cause fires and ex-

plosions. Therefore:

1. Remove all combustible materials well away from the

work area or cover the materials with a protective non-

flammable covering. Combustible materials include wood,

cloth, sawdust, liquid and gas fuels, solvents, paints and

coatings, paper, etc.

2. Hot sparks or hot metal can fall through cracks or

crevices in floors or wall openings and cause a hidden

smoldering fire or fires on the floor below. Make certain

that such openings are protected from hot sparks and

metal."

3. Do not weld, cut or perform other hot work until the

workpiece has been completely cleaned so that there

are no substances on the workpiece which might pro-

duce flammable or toxic vapors. Do not do hot work on

closed containers. They may explode.

4. Have fire extinguishing equipment handy for instant use,

such as a garden hose, water pail, sand bucket, or

portable fire extinguisher. Be sure you are trained in its

use.

5. Do not use equipment beyond its ratings. For example,

overloaded welding cable can overheat and create a fire

hazard.

6. After completing operations, inspect the work area to

make certain there are no hot sparks or hot metal which

could cause a later fire. Use fire watchers when neces-

sary.

7. For additional information, refer to NFPA Standard 51B,

"Fire Prevention in Use of Cutting and Welding Pro-

cesses", available from the National Fire Protection Asso-

ciation, Batterymarch Park, Quincy, MA 02269.

1. Be sure the power source frame (chassis) is connected

to the ground system of the input power.

2. Connect the workpiece to a good electrical ground.

3. Connect the work cable to the workpiece. A poor or

missing connection can expose you or others to a fatal

shock.

4. Use well-maintained equipment. Replace worn or dam-

aged cables.

5. Keep everything dry, including clothing, work area, cables,

torch/electrode holder, and power source.

6. Make sure that all parts of your body are insulated from

work and from ground.

7. Do not stand directly on metal or the earth while working

in tight quarters or a damp area; stand on dry boards or

an insulating platform and wear rubber-soled shoes.

8. Put on dry, hole-free gloves before turning on the power.

9. Turn off the power before removing your gloves.

10. Refer to ANSI/ASC Standard Z49.1 (listed on next page)

for specific grounding recommendations. Do not mistake

the work lead for a ground cable.

1. Welders having pacemakers should consult their physi-

cian before welding. EMF may interfere with some pace-

makers.

2. Exposure to EMF may have other health effects which are

unknown.

3. Welders should use the following procedures to minimize

exposure to EMF:

A. Route the electrode and work cables together. Secure

them with tape when possible.

B. Never coil the torch or work cable around your body.

C. Do not place your body between the torch and work

cables. Route cables on the same side of your body.

D. Connect the work cable to the workpiece as close as

possible to the area being welded.

E. Keep welding power source and cables as far away

from your body as possible.