Troubleshooting Guide - SmartPool NC82S Manual Del Usuario

ERROR
AC OUTLET/GFI
PUMP AND DRIVE
POWER SUPPLY RESET
MOTORS NOT
OPERATING
EXTENSION CORD
LOOSE SWIVEL CONNECTION
BRUSHES WORN
DEBRIS CAUGHT IN WHEELS/BRUSHES/IMPELLER
NOT MOVING
CLEANER CAUGHT ON OBSTRUCTION IN POOL
FILTER FULL
NO SUCTION
DEBRIS IN FAN/IMPELLER
FILTER FULL
DEBRIS CAUGHT IN WHEELS/BRUSHES/IMPELLER
STARTS AND STOPS BRUSHES WORN
CAUGHT ON SOMETHING IN POOL
LOOSE SWIVEL CONNECTION
BACK &
DEBRIS CAUGHT IN WHEELS/BRUSHES/IMPELLER
FORTH/DOING
WHEELIES OR
CLEANER CAUGHT ON OBSTRUCTION IN POOL
SPINNING IN CIRCLES
DEBRIS CAUGHT IN WHEELS/BRUSHES/IMPELLER
FILTER FULL
NOT CLIMBING
BRUSHES WORN
POOL CHEMISTRY (ALGAE GROWTH)
FLOATING CORD NOT BEING UNPLUGGED FROM
POWER SUPPLY REGULARLY
EXCESS CORD IN POOL
CORD TANGLING
CORD NOT BEING UNWOUND BEFORE USE
CORD BEING WRAPPED/STORED INCORRECTLY
AIR TRAPPED
UNIT FLOATING CLEANER CLIMBING TOO HIGH REGULARLY
D.E. PRESENT IN FILTER

TROUBLESHOOTING GUIDE

REASON(S)
CHECK AC OUTLET/RESET THE GFI OR TRY ANOTHER OUTLET
TURN THE POWER SUPPLY OFF AND UNPLUG THE POWER SUPPLY FROM THE AC OUTLET. WAIT 30 SECONDS AND TURN
POWER SUPPLY ON.
TRY PLUGGING THE POWER SUPPLY DIRECTLY INTO AN OUTLET
ENSURE ALL CONNECTIONS TO/FROM THE SWIVEL ARE SECURE.
CHECK BRUSHES AND REPLACE IF NECESSARY
CHECK FOR DEBRIS AND CLEAN WITH A GARDEN HOSE/MAY HAVE TO REMOVE IMPELLER CAP (1 SCREW)
TURN THE CLEANER OFF AND GENTLY PULL ON THE CORD TO REMOVE IT FROM OBSTRUCTION
CLEAN THE FILTER THROUGHLY WITH A GARDEN HOSE
CHECK FOR DEBRIS AND CLEAN WITH A GARDEN HOSE/MAY HAVE TO REMOVE IMPELLER CAP (1 SCREW)
CLEAN THE FILTER THROUGHLY WITH A GARDEN HOSE
CHECK FOR DEBRIS AND CLEAN WITH A GARDEN HOSE/MAY HAVE TO REMOVE IMPELLER CAP (1 SCREW)
CHECK THE BRUSHES AND RING (IF APPLICABLE) FOR WEAR/HOLES WHICH WILL INHIBIT THE CLEANER'S PERFORMANCE
TURN THE CLEANER OFF AND GENTLY PULL ON THE CORD TO REMOVE IT FROM OBSTRUCTION
ENSURE ALL CONNECTIONS TO/FROM THE SWIVEL ARE SECURE.
CHECK FOR DEBRIS AND CLEAN WITH A GARDEN HOSE/MAY HAVE TO REMOVE IMPELLER CAP (1 SCREW)
TURN THE CLEANER OFF AND GENTLY PULL ON THE CORD TO REMOVE IT FROM OBSTRUCTION
CHECK FOR DEBRIS AND CLEAN WITH A GARDEN HOSE/MAY HAVE TO REMOVE IMPELLER CAP (1 SCREW)
CLEAN THE FILTER THROUGHLY WITH A GARDEN HOSE
CHECK THE BRUSHES AND RING (IF APPLICABLE) FOR WEAR. REPLACE IF NECESSARY
HAVE THE WATER CHEMISTRY CHECKED BY A POOL PROFESSIONAL AND/OR BRUSH THE POOL WALLS
MAKE SURE THE CABLE IS BEING UNPLUGGED FROM THE POWER SUPPLY AFTER EVERY 1-2 CYCLES TO RELEASE THE
TENSION THAT BUILDS DURING A CYCLE
ONLY USE THE NECESSARY AMOUNT OF CABLE TO COVER THE POOL EFFICIENTLY
MAKE SURE THE CABLE IS STRAIGHTENED OUT BEFORE THE CYCLE IS STARTED/WALK THE CLEANER THE LENGTH OF THE
POOL TO STRAIGHTENED CORD
WHEN WRAPPING THE CABLE, MAKE LARGE LOOPS AND START AT THE CLEANER END SO THE FREE, PLUG END CAN
UNWIND ANY RESIDUAL TENSION
ROCK THE CLEANER BACK AND FORTH UNDER WATER TO RELEASE ANY TRAPPED AIR
A WEIGHT CAN BE ADDED TO THE CLEANER TO PREVENT IT FROM CLIMBING TOO HIGH AND TO ASSIST IN THE DECENT
BACK TO THE FLOOR
IF THERE IS D.E. IN THE POOL, IT COULD CLOG THE FILTER. CLEAN THE FILTER THOROUGHLY
SUGGESTION(S)
8