Idiomas disponibles
Idiomas disponibles
EURO24M2
GB
+
L1
+
FUSE
10A
FUSE
2A
9 3 10
1
2 3
4
5 6
7
8
M1
230V
FLASH
LAMP
AC
N.O.
N.O.
LED STATE
L1
STATE Led
Lights when the unit is powered
L2
Led RADIO ON
when accessing memory in radio
L3
LED PROG. TIMES
on flashing programming
L4
Led F.C. 2 CLOSING
on when the switch is in N.C.
L5
Led F.C. 2 OPENING
on when the switch is in N.C.
L6
Led PHOTO CLOSING
on with the safety contact closed
L7
Led F.C. 1 CLOSING
on when the switch and in N.C.
L8
Led F.C. 1 OPENING
on when the switch and in N.C.
L7 + L8
Led STOP
both on when the stop and NC
L9
PEDESTRIAN Led
lights when take a pulse pedestrian
L10
Led START
on when you give an impulse
OPERATION LOGIC OF THE SAFETY
Safety band Terminal 15-17 -This contact protects opening and closing.
DIP 5 ON: When there is an obstacle, the engine stop and reverse for 2 sec.
DIP 5 OFF: When there is an obstacle engine STOP
In both cases after the disengagement resumes the opening.
Photocells Terminal 16-17 - This contact protects only in closing
In closing when there is an obstacle engine STOP
Stop Terminal 21-23 - The contact if open will cause the immediate arrest of the automation in any situation.
AMPEROSTOP: In the opening stops and reverses the operation for 2sec. In closing stops and reverses direction.
CRX
+
+
+
PROG
TIME
T1 T2 T3
P2
ON
L3
1 2 3 4 5 6 7 8
DIP SWITCH
1-8
PG2
GATE2
GATE2
L4 L5
L6 L7 L8 L9 L10
11
25 26 27 28 29 12 13 14 15
16 17 18 19 20 21 22 23 24
M2
FCA2
PHOTO
33V 0V 24V
LOCK
FCC2
COSTA
TRIMMER T1
The Trimmer Power regulates
the power and sensitivity in
working.
TRIMMER T2
The Trimmer Power Slow
regulates the power and
sensitivity in slow down mode.
TRIMMER T3
The Trimmer Break regulates the
break time from 3 to 120 sec
TECHNICAL FEATURES
POWER
POWER ENGINE
OUTPUT ACCESORIES
ANT
OUTPUT FLASH, OUTPUT COURTESY LIGHT
TIME FOR AUTOMATIC CLOSE
VDS
TIME FOR MANEUVER
TIME FOR COURTESY LIGHT
NR CODES STORABLE
PROG
TRANSMITERS TYPE
RADIO
FREQUENCY
P1
TEMPERATURE TO WORK
SENSIBILITY
L2
HOMOLOGATION
J1
TERMINAL
EXT
1-2
PG1
3
GATE1
4-5
M2
M2
M1
6-7
8-9
10-11
12-14com
13-14com
15-17com
16-17com
PED
FCC1
19-18com
STOP
START
FCA1
20-18com
21-23com
22-23com
24-23com
25-26negativo 33Vdc
27-26negativo 24Vdc
28-29
30-31
32-33
34-35
-
+
BUTTON P1
RADIO PROG, for storage remote controls
BUTTON P2
PROG TIME, for storage the stroke
JUMPER J1 =
You can insert the external receivers with the connector CRX. So you
can increase the memory or change the frequency.
Insert bridge.
230V AC +/- 10%
24 Vdc
33V / 24V DC 250mA
Max 10A a 230V
5 a 120 sec
3 a 120 sec
180 sec
254 code
Fix\ Roll-code
433.92 / 868 Mhz
-20 a 70°C
Better off –100dBm
Conf ETS 300-220/ETS 300-683
TIP
DESCRIPTION
230Vac
Power 230Vac
Ground
Free
FLASH (max output 230V 10A)
Free
LAMP of courtesy (max output Max 230V 10A)
24Vdc
ENGINE1
24Vdc
ENGINE2
N.C.
Limit switch closing ENGINE2(if not use make the bridge)
N.C.
Limit switch opening ENGINE2(if not use make the bridge)
N.C.
Safety band or opening photocells (if not use make the bridge)
N.C.
Closing photocells(if not use make the bridge)
N.C.
Limit switch closing ENGINE1(if not use make the bridge)
N.C.
Limit switch opening ENGINE1(if not use make the bridge)
N.C.
STOP contact (if not use make the bridge)
N.O.
PEDESTRIAN contact
N.O.
START contact
Power service or battery charger (output 33Vdc 250mA)
Power service or accessories (output 24Vdc 250mA)
12Vdc
Electric lock
24Vac
Secondary input Transfomator 24Vac
230Vac
Primary input Transformator 230Vac
Input Antenna (35 signal)
BUTTON PG1
GATE1 For the programming stroke of the first leaf
or start command.
BUTTON PG2
GATE2 For the programming stroke of the second
leaf or pedestrian opening.
Selection storage radio INTERNAL EXTERNAL
INTERNAL
EXTERNAL
