Tabla de contenido
OVERVIEW
Thank you for choosing the Invisia Toilet Roll Holder. Please read and
understand the instructions in this manual; keep manual for future
reference. It is your responsibility to see that your Invisia Toilet Roll Holder
is properly assembled, installed, and cared for. Failure to follow instructions
in this manual could result in serious injury or death. If you are not
equipped to undertake the outlined work, we would recommend that you
have your Invisia Toilet Roll Holder installed by a qualified contractor.
The Invisia Toilet Roll Holder is a combination grab bar and toilet roll
holder, designed to disguise safety in a bathroom accessory. The Invisia
Toilet Roll Holder is intended for moderate vertical and horizontal load
bearing to provide sitting and standing support for people with reduced
mobility. The Invisia Toilet Roll Holder is installed with appropriate fasteners
to a structural wall. The paper axle (which holds a roll of toilet paper) is
NOT intended to be a support product. The maximum user weight for this
product is 500lbs / 227kgs. Note: Product is not intended to support full
body weight. The Invisia Toilet Roll Holder is not to be used in any other
way than described above.
LIMITED LIFETIME WARRANTY
Products are covered by a limited lifetime warranty against defects in
materials and workmanship for the original purchaser. Warranty excludes
products that have been damaged through misuse, accidental damage,
alteration, normal wear and tear, wood material and stain, or the use of
corrosive or abrasive cleaning products.
Buyer hereby indemnifies, agrees to hold harmless and defend HealthCraft
Products Inc. from and against any and all liabilities, claims, (founded and
unfounded), losses, damages, costs and expenses (including without
limitation consequential damages and reasonable professional fees)
resulting from buyers specification, application, or improper use of goods
described hereon; buyers omission or neglect. HealthCraft Products Inc.
does not assume any liability for damage resulting from services performed
by others or faulty installation, misuse or misapplication of goods sold by
HealthCraft Products Inc. HealthCraft Products Inc. shall not be liable for
prospective profits or special, indirect, or consequential damages, or for the
cost of any corrective work done without HealthCraft Products Inc. prior
approval. HealthCraft Products Inc. total liability hereunder shall in no
event exceed the purchase price of the goods specified hereon.
Specifications subject to change without notice.
HealthCraft Products Inc.
2790 Fenton Road
Ottawa, Canada
K1T 3T7
10
English
Gate 88
Kanalgatan 45B
Skellefteå, Sweden
EC
REP
93123
DELIVERY CONTENTS / TOILET ROLL HOLDER
1. Rail (Toilet Roll Holder)
2. Wall Stem Assembly
3. #10-32 Set Screw
4. Paper Axle
5. Center Punch
6. 3/32" Hex Key
INSTALLATION WARNINGS
1. Rail must be installed to walls that are structurally sound. If desired
installation location does not have adequate structure, add wood blocking.
2. For different wall constructions, use appropriate fastener combination
(Note: reduced weight capacity when not full structure).
3. If using supplied hollow wall anchors, ensure center screw holes align
with vertical wood stud.
4. CAUTION - Do not install if there is no structure behind drywall.
5. CAUTION - Do not install if structure behind walls is unknown.
6. CAUTION - Do not install into metal studs.
7. CAUTION - Rail and bathtub are slippery when wet.
SUGGESTED TOILET ROLL HOLDER LOCATIONS
To determine the optimal mounting location, we recomment holding the rail
in place and walking through the motions of a transfer (sitting, standing,
reaching ,etc.). Recommended rail height 24-36" / 610-914mm.
INSTALLATION
1. Back off set screw from rail socket.
2. Allow wall stem to freely move in and out of rail socket.
3. Peel off label on back of wall stem to expose sticker.
4. Mark location of top wall stem.
5. Drill pilot hole appropiate for fastener.
6. Fasten the wall stem to the wall using supplied lock washer and
fastener.
7. Place rail back onto the fastened wall stem.
8. Using wall plate as guide, mark location of bottom holes. Ensure level.
9. Drill pilot holes appropiate for fasteners.
10. Place rail back onto the fastened wall stems, and secure rail to wall
stem by tightening set screws.
11. Secure the wall plate to the wall using appropriate fasteners (x3).
12. Cover exposed screw heads with push on plastic caps (x3).
Inspect hardware regularly, and tighten if required.
TECHNICAL DATA
See Figure E.
PRODUCT USAGE
See Figure F.
FIGURE A.
7. Lock Washer, S/S (x1)
8. Plastic Cap (x3)
9. #10 Wood Screw, S/S (x1)
10. #10 Wood Screw CSK, S/S (x3)
11. 3/16" Bolt, S/S (x2)
12. Hollow Wall Anchor (x2)
FIGURE B.
FIGURE C.
FIGURE D.
Tabla de contenido
