Manuales relacionados para Truper TAL-3/8N2
Resumen de contenidos para Truper TAL-3/8N2
- Página 1 Manual Drill 0.5 Hp 3/8” Power Chuck Applies for: Model Code TAL-3/8N2 16706 TAL-3/8N2 Read this manual thoroughly CAUTION before using the tool.
-
Página 2: Tabla De Contenido
Manual before Parts using the tool. Start up Keep this manual for future references. Maintenance The illustrations in this manual are for reference Notes only. They might be different from the real tool. Authorized Service Centers Branches Warranty policy TAL-3/8N2 ENGLISH... -
Página 3: Technical Data
Technical data TAL-3/8N2 Code 16706 Description Drill Chuck 3/8” Voltage 127 V Frequency 60 Hz Current 3,1 A Power 0.5 Hp Speed 0 - 3 000 r/min Duty cycle 50 minutes work per 20 minutes idle. Maximum 6 hours per day. -
Página 4: General Power Tools Safety Warnings
General power tool safety warnings WARNING! Read carefully all safety warnings and instructions listed below. Failure to comply with any of these warnings may result in electric shock, fire and / or severe damage. Save all warnings and instructions for future references. -
Página 5: Safety Standards For Drills And Hammer Drills
Safety Standards for drills and hammer drills Choose the right bit While operating the hammer drill CAUTION • Choose the right bit for the work piece. • Use the auxiliary handles, if supplied with the tool. It reduces the risk of severe injury and makes the job easier. Loss of control may result in personal injury. -
Página 6: Parts
Parts Chuck Continuous Speed Rotation use button control direction lever Handle Power cord Switch Chuck Chuck wrench wrench holder ENGLISH... -
Página 7: Start Up
Start up Chuck Bit fitting • Put the bit into the chuck until it stops. Fasten with the chuck wrench and tighten alternatively the chuck into each of the orifices. Start up and operation control • Intermittent operation: Connect the plug into the power outlet. Chuck wrench Press the switch (A) to start the drill. -
Página 8: Maintenance
Maintenance Cleaning and care Lubrication • Keep the vent slots clean and without obstructions to • We recommend taking the tool to a guarantee adequate motor cooling. Authorized Service Center to lubricate the drive wheel • Inspect every now and then all the mounting screws and every time replacing carbon brushes is needed. -
Página 9: Notes
Notes ENGLISH... -
Página 10: Authorized Service Centers
Authorized Service Centers In the event of any problem contacting a Service Center, please see our webpage www.truper.com to get an updated list, or call our toll-free numbers 01(800) 690-6990 or 01 (800) 018-7873 to get information about the nearest Authorized Service Center. - Página 11 HUMBOLT SUR No. 49, COL. CENTRO C.P. 91270 PEROTE, INDEPENDENCIA No. 1323 COL. LA PIRAGUA, TUXTEPEC VER. TEL.: 01(282) 832-0327 | 825-6408 C.P. 68300 TEL.: 01(287) 875-1363 670397 LA CASA DISTRIBUIDORA TRUPER CALLE 671420 DISTRIBUIDORA DE HERRAMIENTAS PUEBLA URUGUAY No. 713, COL. 27 DE SEPTIEMBRE C.P. 93320, MANUALES ZAVALETA, S.A.
-
Página 12: Branches
This warranty shall be effective when presenting the product and the valid Warranty policy duly stamped by the supplier or the proof of purchase. To comply with this warranty, Truper will cover transportation expenses in case consumer’s address is out of range from Authorized Service Centers listed herein or at the website www.truper.com or at our toll-free numbers: 01 (800) 690-6990 or 01(800) 018-7873.