Idiomas disponibles

Idiomas disponibles

Enlaces rápidos

VESTIL MANUFACTURING CORPORATION
2999 North Wayne Street
Angola, IN 46703 USA
Phone (260) 665-7586 • Fax (260) 665-1339
[email protected] • www.vestil.com
Ergonomic Solutions
Contents
Warnings and Safety Instructions ................. 1
Receiving Instructions .................................. 1
Operating Instructions .................................. 1
WARNINGS & SAFETY INSTRUCTIONS
Read owner's manual completely before operating unit!
• Keep hands and feet away from all moving parts while
table is in use.
• Do not attempt to adjust the height or tilt angle of the
table while a load is sitting on the platform.
• Never stand or sit on the table.
• Remove load before performing any repairs on the table.
• Use only maintenance parts supplied or approved by
the manufacturer.
• Always engage all wheel brakes when table is not being
moved.
• Never exceed the maximum loading capacity of 300 lbs.
• Load must be evenly distributed on table to ensure
maximum stability.
• Always make sure the height adjustment screw is
securely tightened before a load is applied especially
after table has been raised or lowered.
• Failure to follow these guidelines may result in personal
injury and/or property damage.
RECEIVING INSTRUCTIONS
Every unit is thoroughly tested and inspected prior
to shipment. However, it is possible that the unit may incur
damage during transit. If you see damage when unloading
make a note of it on the SHIPPER RECEIVER.
Remove all packing and strapping material and
inspect for damage. IF DAMAGE IS EVIDENT, FILE A
CLAIM WITH THE CARRIER IMMEDIATELY!
OPERATING INSTRUCTIONS (WT-2424)
1) Position the work table near the desired work area.
2) Lock all four casters.
Revised 09-04
A company dedicated to solving ergonomic and material
handling problems since 1955 .
OWNER'S
MANUAL
TILTING WORK TABLE
MODEL WT-2424 & WT-2221
Caster Installation........................................... 2
Parts Identification & Drawing (WT-2424) ...... 3
Parts Identification & Drawing (WT-2221) ...... 4
3) Loosen the height adjustment screw and adjust the
work table to the desired height using the handwheel
located on the base frame.
4) Tighten the height adjustment screw.
5) Adjust the tilt angle of the table to the desired position
using the handwheel directly under the table platform.
6) Place the load on table carefully.
OPERATING INSTRUCTIONS (WT-2221)
1) Position the work table near the desired work area.
2) Lock all four casters.
3) Adjust the height to the correct level by star knob
adjustment located on the center column and sliding it
up or down.
4) Loosen the tilt adjustment knob under platform. Tilt
deck to desired angle and retighten.
5) Place the load on the table.
TILTING WORK TABLE
MODEL WT-2424 & WT-2221
16-126-107
E
N
G
L
I
S
H
E
S
P
A
N
O
L
F
R
A
N
Ç
A
I
S
1

Capítulos

Tabla de contenido
loading

Resumen de contenidos para Vestil WT-2424

  • Página 5: Tabla De Contenido

    • www.vestil.com Soluciones Ergonómicas MANUAL DEL PROPIETARIO MESA DE TRABAJO BASCULANTE MODELO WT-2424 & WT-2221 Contenido Instrucciones de Montaje de las Ruedas ..6 Instrucciones de seguridad y advertencia ..5 Identificación de partes y dibujos ....... 7 Instrucciones de recibo ........5 Lista de partes y dibujos ........
  • Página 6: Instrucciones De Montaje De Las Ruedas

    INSTRUCCIONES DE MONTAJE DE LAS RUEDAS Asegure y levante un lado del armazón del carro lo suficentemente alto para que las ruedas se puedan poner en ese lado. Usted vera cuatro soportes de montaje de ruedas solados por debajo del armazón, uno en cada esquina. Si tiene las dos ruedas giratorias y rigidas, las ruedas se deben montar en pares juntos.
  • Página 7: Identificación De Partes Y Dibujos

    IDENTIFICACIÓN DE PARTES 19 & 19A Aceite levemente los tornillos #8y #12 semestralmente ó según se requiera. NO. DE INGENIERO NO. PARTE PARTIDA NO. DESCRIPTIÓN CTD. 16-513-003 WT-TAB Partes superior de la mesa soldadas 37024 10 mm Tuerca de nilon 10mm x 76mm UNC H.H.C.S.
  • Página 8: Lista De Partes Explosivas Modelo Wt-2221

    LISTA DE PARTES EXPLOSIVAS MODELO WT-2221 PARTIDA DESCRIPCIÓN NO. DE INGENIERO NO. PARTE CTD. Manivela de ajuste de inclinación 16-025-008 WTP-HTA WTP-BLT Perno 1.27 cm - 13 x 6.9 cm 11214 WTP-NN-1 1.27 cm - 13 Tuerca de nylock 37030 Rueda giratoria 16-132-072 WTP-SCSTR...

Este manual también es adecuado para:

Wt-2221

Tabla de contenido