Idiomas disponibles
Idiomas disponibles
PRECAUCIÓN: Nunca intente abrir la unidad de alimentación por ningún motivo. Si la caja
plástica de la unidad de alimentación se triza o rompe, llévela a un centro de servicio para su
reciclaje.
RECOMENDACIONES DE ALMACENAMIENTO
1. El mejor almacenamiento es uno fresco y seco - lejos de la luz directa del sol y del exceso
de calor o frío.
2. El almacenamiento de la unidad de alimentación por períodos largos de tiempo no dañará
la unidad de alimentación o el cargador. Bajo las condiciones correctas, pueden ser almace-
nados por 5 años o más.
SAFETY INSTRUCTIONS FOR INTELLIGENT CHARGERS
WARNING: Read and understand all instructions. Failure to follow all instructions listed
below may result in electric shock, fire and/or serious personal injury.
Important Safety Instructions for Battery Chargers;
SAVE THESE INSTRUCTIONS: This manual contains important safety and operating
instructions for the CHAR18V, CHAR16VA, CHAR144V & CHAR12VA battery chargers.
• Before using charger, read all instructions and cautionary markings on charger, battery pack,
and product using battery pack.
DANGER: Electrocution hazard. 120 volts are present at charging terminals. Do not probe
with conductive objects. Electric shock or electrocution may result.
WARNING: Shock hazard. Do not allow any liquid to get inside charger. Electric shock may
result.
CAUTION: Under certain conditions, with the charger plugged in to the power supply, the
exposed charging contacts inside the charger can be shorted by foreign material. Foreign
materials of a conductive nature such as, but not limited to, steel wool, aluminum foil, or any
buildup of metallic particles should be kept away from charger cavities. Always unplug the
charger from the power supply when there is no battery pack in the cavity. Unplug charger
before attempting to clean.
• DO NOT attempt to charge the battery pack with any chargers other than the ones in this
manual. The charger and battery pack
are
specifically
designed
to
work
together.
• These chargers are not intended for
any uses other than charging DEWALT
rechargeable batteries. Any other uses
may result in risk of fire, electric shock or
electrocution.
• Do not expose charger to rain or snow.
• Pull by plug rather than cord when disconnecting charger. This will reduce risk of damage to
electric plug and cord.
• Make sure that cord is located so that it will not be stepped on, tripped over, or otherwise
subjected to damage or stress.
• Do not use an extension cord unless it is absolutely necessary. Use of improper extension
cord could result in risk of fire, electric shock, or electrocution.
• "THIS PRODUCT HAS A 'Y' CLIP CABLE, IN CASE OF DAMAGE TAKE IT TO AN AUTHORIZED
SERVICE CENTER FOR REPAIR".
• Do not place any object on top of charger or place the charger on a soft surface that might
block the ventilation slots and result in excessive internal heat. Place the charger in a position
away from any heat source. The charger is ventilated through slots in the top and the bottom
of the housing.
• Do not operate charger with damaged cord or plug — have them replaced immediately.
• Do not operate charger if it has received a sharp blow, been dropped, or otherwise damaged
in any way. Take it to an authorized service center.
• Do not disassemble charger; take it to an authorized service center when service or repair is
required. Incorrect reassembly may result in a risk of electric shock, electrocution or fire.
• Disconnect the charger from the outlet before attempting any cleaning. This will reduce the
risk of electric shock. Removing the battery pack will not reduce this risk.
• NEVER attempt to connect 2 chargers together.
• The charger is designed to operate on standard 120V household electrical power. Do not
attempt to use it on any other voltage.
OPERATION
The CHAR20/18V, CHAR14V & CHAR12V battery chargers are designed to charge Li-Ion URREA
battery packs with voltage from 6 up to 20 volts. Time of chargins is at is follows; CHAR20/18V
and CHAR14V time of chargin it's in about one hour, as for CHAR12V it takes 35 minutes.
These chargers require no adjustment and are designed to be as easy as possible to operate.
Simply place your battery pack into a receptacle of a plugged in charger and it will automati-
cally charge the pack.
CAUTION: When not in use, place tool on its side on a stable surface where it will not cause
a tripping or falling hazard. Some tools with large battery packs will stand upright on the
battery pack but may be easily knocked over.
BATTERY PACKS
The battery pack is not fully charged out of the carton. Before using the battery pack and
charger, read the safety instructions below. Then follow charging procedures outlined.
• Do not incinerate the battery pack even if it is severely damaged or is completely worn out.
The battery pack can explode in a fire.
• A small leakage of liquid from the battery pack cells may occur under extreme usage or
temperature conditions. This does not indicate a failure. However, if the outer seal is broken
and this leakage gets on your skin:
a. Wash quickly with soap and water.
b. Neutralize with a mild acid such as lemon juice or vinegar.
c. If battery liquid gets into your eyes, flush them with clean water for a minimum of 10
minutes and seek immediate medical attention. (Medical Note: The liquid is 25-35% solution
of potassium hydroxide.)
• Charge the battery packs only in URREA chargers.
• DO NOT splash or immerse in water or other liquids.
• Do not store or use the tool and battery pack in locations where the temperature may reach
or exceed 105°F (40°C) (such as outside sheds or metal buildings in summer).
DANGER: Electrocution hazard. Never attempt to open the battery pack for any reason. If
battery pack case is cracked or damaged, do not insert into charger. Electric shock or
electrocution may result. Damaged battery packs should be returned to service center for
recycling.
WARNING: Fire hazard. Do not store or carry battery so that metal objects can contact
exposed battery terminals. For example, do not place battery in aprons, pockets, tool boxes,
product kit boxes, drawers, etc., with loose nails, screws, keys, etc. without battery cap.
Transporting batteries can possibly cause fires if the battery terminals inadvertently come in
contact with conductive materials such as keys, coins, hand tools and the like. The US
Department of Transportation Hazardous Material Regulations (HMR) actually prohibit
E N G L I S H
transporting batteries in commerce or on airplanes (i.e., packed in suitcases and carry-on
luggage) UNLESS they are properly protected from short circuits. So when transporting
individual batteries, make sure that the battery terminals are protected and well insulated
from materials that could contact them and cause a short circuit.
IMPORTANT CHARGING NOTES
1. Longest life and best performance can be obtained if the battery pack is charged when the
air temperature is between 65°F and 75°F (18°- 24°C). DO NOT charge the battery pack in an
air temperature below +40°F (+4.5°C), or above +105°F (+40.5°C). This is important and will
prevent serious damage to the battery pack.
2. The charger and battery pack may become warm to touch while charging. This is a normal
condition, and does not indicate a problem. To facilitate the cooling of the battery pack after
use, avoid placing the charger or battery pack in a warm environment such as in a metal shed,
or an uninsulated trailer.
3. If the battery pack does not charge properly:
a. Check current at receptacle by plugging in a lamp or other appliance
b. Check to see if receptacle is connected to a light switch which turns power off when you
turn out the lights.
c. Move charger and battery pack to a location where the surrounding air temperature is
approximately 65°F - 75°F (18°- 24°C).
d. If charging problems persist, take the tool, battery pack and charger to your local service
center.
4. The battery pack should be recharged when it fails to produce sufficient power on jobs
which were easily done previously. DO NOT CONTINUE to use under these conditions. Follow
the charging procedure. You may also charge a partially used pack whenever you desire with
no adverse affect on the battery pack.
5. Under certain conditions, with the charger plugged into the power supply, the exposed
charging contacts inside the charger can be shorted by foreign material. Foreign materials of
a conductive nature such as, but not limited to, steel wool, aluminum foil, or any buildup of
metallic particles should be kept away from charger cavities. Always unplug the charger from
the power supply when there is no battery pack in the cavity. Unplug charger before
attempting to clean.
6. Do not freeze or immerse charger in water or any other liquid.
WARNING: Shock hazard. Don't allow any liquid to get inside charger. Electric shock may
result.
CAUTION: Never attempt to open the battery pack for any reason. If the plastic housing of
the battery pack breaks or cracks, return to a service center for recycling.
STORAGE RECOMMENDATIONS
1. The best storage place is one that is cool and dry away from direct sunlight and excess heat
or cold.
2. Long storage will not harm the battery pack or charger. Under proper conditions, they can
be stored for 5 years or more.
CHAR18V
ENTRADA DEL CARGADOR /CHARGER INPUT:
120 V ~ 60 Hz
SALIDA DEL CARGADOR /CHARGER OUTPUT:
18 V
1,5 A
COMPATIBILIDAD /COMPATIBILITY: RB1018
PESO /WEIGHT: 320 g (0,75 lb)
CHAR16VA
ENTRADA DEL CARGADOR /CHARGER INPUT:
120 V ~ 60 Hz
SALIDA DEL CARGADOR /CHARGER OUTPUT:
16 V
1,8 A
COMPATIBILIDAD /COMPATIBILITY: RB916
PESO /WEIGHT: 320 g (0,75 lb)
P O L I Z A D E G A R A N T Í A
W A R R A N T P O L I C Y
Urrea Herramientas Profesionales S.A. de C.V. km 11,5 Carretera A El Castillo, El Salto, Jalisco, México. C.P. 45680, Tel. (33) 3208
7900, RFC UHP900402Q29, garantiza este producto por el termino de 1 año en sus piezas, componentes y mano de obra contra
cualquier defecto de fabricación a partir de la fecha de entrega.
Condiciones: Para hacer efectiva la garantía deberá presentar el producto junto con la poliza de garantia debidamente firmada
y sellada por el establecimiento donde la adquirio, en cualquiera de los centros de servicio autorizados.
Los gastos de transportación que se deriven del cumplimiento de la garantía seran cubiertos por Urrea Herramientas Profesiona-
les S.A. de C.V.
Esta garantía no será valida en los siguientes casos:
· Cuando el producto haya sido utilizado en condiciones distintas a las normales o al desgaste natural de sus partes.
· Cuando el producto no haya sido operado de acuerdo al instructivo de uso que lo acompaña.
· Cuando el producto haya sido alterado o reparado por personas no autorizadas.
Urrea Herramientas Profesionales S.A. de C.V. km 11,5 Carretera A El Castillo, El Salto, Jalisco, México. C. P. 45680, Tel. (33) 3208 7900,
RFC UHP900402Q29, warranties this product for a period of 1 year in its parts, components and manual labour against any manufacture
defect from the purchasing date.
Terms: In order to make warranty effective you must present the product along with the warranty properly fillled and signed to an authorized
distributor or service center. Urrea Herramientas Profesionales S.A. de C.V. will cover the transportation cost related to the warranty.
This warranty is not applicable in the following cases:
· When the product has not been used according to normal
conditions or natural wear of its parts.
· When the product has not been used according with this user's
manual instructions.
· When the product has been fixed or modified by unauthorized or
unqualified person.
CHAR144V
ENTRADA DEL CARGADOR /CHARGER INPUT:
120 V ~ 60 Hz
SALIDA DEL CARGADOR /CHARGER OUTPUT:
14,4 V
1,5 A
COMPATIBILIDAD /COMPATIBILITY: RB914A
PESO /WEIGHT: 320 g (0,75 lb)
CHAR12VA
ENTRADA DEL CARGADOR /CHARGER INPUT:
120 V ~ 60 Hz
SALIDA DEL CARGADOR /CHARGER OUTPUT:
12 V
1,5 A
COMPATIBILIDAD /COMPATIBILITY: TB912
PESO /WEIGHT: 225 g (0,49 lb)
Sello del distribuidor/
Distributor seal:
Fecha /Date:______/ ______/ ______
