Battery; Battery Charger; Accessories; Installation Information - gtm SIGMA1 E Manual Del Usaurio

2 GENERAL ON/OFF KEY - BATTERY CU-
TOUT SWITCH
3 BRUSH MOTOR THERMAL BREAKER
4 TRACTION MOTOR THERMAL BREAKER
5 SUCTION MOTOR SWITCH
6 BRUSH MOTOR SWITCH
7 FORWARD/REVERSE SELECTOR SWITCH
PHOTO H SIGMA1 BTR
1 HOUR METER
2 EMERGENCY BUTTON SWITCH
3 FORWARD/REVERSE TRACTION HAN-
DLE
4 BRAKE LEVER
5 SQUEEGEE LIFT/LOWER LEVER
6 RECOVERY TANK INSPECTION PLUG
7 BRUSH PLATE LIFT/LOWER PEDAL
8 RECOVERY TANK DRAIN HOSE
9 BATTERY CHARGER CONNECTOR
10 WATER OUTLET ADJUSTING LEVER
PHOTO I SIGMA1 BM - BTR
BATTERY CONNECTION DIAGRAM
PHOTO L SIGMA1 BM - BTR
1 BATTERY COMPARTMENT WITH 12V
BATTERIES
2 BATTERY CONNECTION DIAGRAM
PHOTO M SIGMA1 BM - BTR
1 SELECTOR SWITCH FOR PB-ACID / GEL
BATTERIES
PHOTO N SIGMA1 BM - BTR
1 SOLUTION WATER FILTER
2 SOLUTION WATER TANK DRAIN PLUG
PHOTO O SIGMA1 E - BM - BTR
1 SUCTION HOSE
2 SQUEEGEE INCLINATION ADJUSTING
KNOB
3 SQUEEGEE PRESSION ADJUSTING KNOB
4 SQUEEGEE BUMPER WHEEL
5 SQUEEGEE BLADES REPLACEMENT
KNOB
6 SQUEEGEE WHEEL
7 SQUEEGEE FIXING KNOB
PHOTO P SIGMA1 E - BM - BTR
1 SPLASH GUARD FIXING SPRING CLIP
2 SPLASH GUARD

5.2.2 BATTERY

If supplied, the Pb-Acid (if not dry charged) or gel
batteries are ready to be installed:
Positive pole - red
Negative pole - black

5.2.3 BATTERY CHARGER

If supplied, refer to the corresponding booklet.

5.3 ACCESSORIES

Your machine supplier can provide a complete and
updated list of all available accessories, such as
brushes, scrapers, disks, etc.

6. INSTALLATION INFORMATION

6.1 BATTERY PREPARATION

!
( ) The technical features of the batteries used
must match those indicated in the technical featu-
res section. Using different batteries may cause se-
rious damage to the machine or may require them
to be charged more frequently.
( ) During installation or when performing any
type of battery maintenance, the operator must be
equipped with adequate safety accessories to pre-
vent accidents. Work far from open flames, do not
short-circuit the battery poles, do not generate
sparks and do not smoke.
The batteries are normally supplied full of acid so-
lution (for the Pb-Acid type) and ready for use. In
any case, follow the steps indicated in the manual
supplied with the battery and carefully follow the
instructions regarding safety and operating proce-
dures.
6.2 BATTERY INSTALLATION AND PREPARA-
TION
!
( ) These operations must be carried out by spe-
cialised personnel.
Disconnect the Anderson connector of the battery
wiring from the Anderson connector of the machine
wiring. Always hold the connectors with the hands
and never pull on the cables.
( ) Attach the battery wiring to the battery,
connecting the terminals only on the poles
marked with the same symbol (red wiring
"+", black wiring "-")! A battery short-circuit
may cause an explosion!
After checking that all the controls on the panel are
in position "0" or at rest, connect the battery con-
nector to the machine connector.
!
( ) Close the battery compartment making sure
not to crush any wires.
6.3 SETTING OF THE ELECTRONIC BOARD
FOR THE SECURITY STOP OF THE BRUSH
MOTOR
In order to avoid the complete discharge of the bat-
teries, the machine is provided with a safety device.
When charge of the batteries goes below the sa-
fety threshold, the electronic card (Photo M) stops
the operation of the brush motor.
☞
( ) The operator must stop its work and re-
charge the batteries.
32