Tabla de contenido
Note:
If only the large, red light segment on the left is illuminated, your
energizer is set to address zero.
This means that you have an energizer configured to ignore commands
from a Remote Control Handset.
Changing the energizer's address setting
To switch to the Standby mode:
1
Switch off the power supply to the energizer and wait for 5
minutes, then switch on the power supply again.
2
Press
to switch on the remote control.
3
Hold the remote control within 150 to 300 mm (6 to 12") of the
energizer, then press
. The energizer will stop pulsing (may
take up to 2 seconds) and only the large, green light on the right
will continue flashing.
4
Press
to switch off the remote control.
To change the energizer's address:
1
Switch to the Standby mode. See the procedure above.
2
Press and hold
, then press
3
Press and hold
to scroll through the list of available options.
4
Select the Address (Ad) option, and press
you want is displayed.
5
Hold the remote control within 150 to 300 mm (6 to 12") of the
energizer, then press
energizer.
A moving arrow on the remote control screen indicates that the
command is being sent to the energizer. The large, red light on
the left of the energizer's LED display illuminates for 6 seconds as
the energizer receives the command. The energizer then resumes
in Standby mode with only the large, green light on the right
flashing.
6
Press
to switch off the remote control.
To exit the Set-up mode without changing the energizer's address:
Instead of pressing
, which transmits the new setting, press
•
. This switches off the remote control.
Tip:
Make a note of the address setting of the energizer to save time
should the address be accidentally changed, or if an additional remote
control is required in the future.
To reduce the risk of accidental address changes, the energizer has
been built with the following safeguards:
It will accept a new address only
•
supply being switched on.
It will accept a new address only when in Standby mode (that is,
•
when the energizer is not pulsing).
Activating the remote control function of an energizer
supplied without a Remote Control Handset
An energizer purchased without a Remote Control Handset in the same
package will not respond to commands sent by a remote control until
the remote control function has been activated in the energizer.
to enter the Set-up mode.
until the number
to transmit the new setting to the
within four minutes
of the power
13
Before activating the remote control function:
Switch off the power supply to the energizer and wait for 5
•
14
minutes, then switch on the power supply again.
15
To activate the remote control function:
1
Press and hold
the Set-up mode.
2
Press and hold
3
Select the Address (Ad) option, and press
you want is displayed.
4
Hold the remote control within 150 to 300 mm (6 to 12") of the
energizer, then press
energizer.
A moving arrow on the remote control screen indicates that the
command is being sent to the energizer. The large, red light on
the left of the energizer's LED display illuminates for 6 seconds as
the energizer receives the command. The energizer then resumes
in Standby mode with only the large, green light on the right
flashing.
5
Press
to switch off the remote control.
Tip:
Make a note of the address setting of the energizer to save time
should the address be accidentally changed, or if an additional remote
control is required in the future.
Building a permanent electric fence
Components of an electric fence
An electric fence system comprises the following elements:
An energizer.
•
An earth system.
•
into the ground, which are connected to the Fence earth terminal
on the energizer.
Insulated underground cables.
•
the earth and fence.
An insulated fence.
•
energizer. Fences can be made to a variety of designs (see below).
Other useful components that can be added:
Cut-out switches
you to isolate sections of the fence for repair.
Lightning diverter kit
energizer from lightning conducted down the fence line.
Typical installation
The animal receives a shock when it completes a circuit between the
fence and the earth system. The fence below has all live wires and
requires conductive soils. These fences are often referred to as 'all-live'
or 'earth-return' fences.
on the remote control, then press
to scroll through the list of available options.
until the number
to transmit the new setting to the
This comprises a number of metal rods inserted
Used to connect the energizer to
Connected to the Fence output terminal of the
. Installed at regular intervals, these allow
. Used to minimise the damage to your
to enter
5
Tabla de contenido
