Oiling Chain; Filling Oil Tank - MTD Yard Machines PS Manual Del Operador

For Parts Call 606-678-9623 or 606-561-4983 For Parts Call 606-678-9623 or 606-561-4983
UNLOCK
DÉVERROUILLEZ
ABRA
1. To extend the pole, loosen coupling by turning coupling
nut counterclockwise as shown in Fig. 8. Pole will slide
freely.
2. Pull inner pole section out to desired length of exten-
sion. Note: Only extend pole to minimum length
required to reach limb that is being cut.
3. To lock pole in position, tighten coupling by turning cou-
pling nut clockwise (See Fig. 8) until firmly hand tight.
Make sure saw handle is aligned with pole handle
before tightening coupling nut.
IMPORTANT: Do not use wrench or pliers to overtight-
en coupling. Damage to coupling or pole may result.

OILING CHAIN

To oil chain, press oil cap. Oil will feed onto guide bar and
chain. Press oil cap at least once before each cut. Always
check oil level before using pole saw. check oil level often
by looking at oil sight level hole. Oil sight level hole is on left
side of saw, between front handle and front hand guard. Do
not attempt to operate the oiler while cutting with the pole
saw.
Grip Area
Zone de Poignée
Área del Apretón
Lock-Off Switch
Gâchette de Contact
Fijador del Interruptor
Fig.10
ASSEMBLY INSTRUCTIONS
LOCK
SERRURE
BLOQUEO
Fig.8
Fig.9
Trigger Switch
Interrupteur de Gachette
Interruptor de Gatillo
www.mymowerparts.com www.mymowerparts.com
CUTTING WITH THE POLE SAW
1. Connect saw to extension cord. Connect extension cord
to power supply.
2. Use both hands to grip pole saw. Use only designated
grip areas when operating pole saw (See Fig. 9). Use
firm grip. Thumbs and fingers must wrap around pole
saw handle and pole.
3. Make sure your footing is firm. Keep feet apart. Divide
your weight evenly on both feet.
4. When ready to make a cut, press in trigger switch lock-
off and squeeze trigger switch (see Fig. 10) This will
turn pole saw on. Releasing trigger switch will turn pole
saw off. Make sure saw is running at full speed before
starting a cut.
5. When starting a cut, place moving chain against wood.
Hold pole saw firmly in place to avoid possible bouncing
or skating (sideways movement) of saw.
6. Guide pole saw using light pressure. Do not force pole
saw. The motor will overload and can burn out. It will do
the job better and safer at the rate for which it was
intended.
7. Remove pole saw from a cut with saw running at full
speed. Stop pole saw by releasing trigger. Make sure
chain has stopped before setting pole saw down.
8. Never stand directly under the limb you are trimming.
Always position yourself out of the path of falling debris.

FILLING OIL TANK

Using a funnel, fill oil tank with MTD Chain, Bar and
Sprocket oil. Wipe up any spills. Make sure no dirt gets into
the oil tank.
SELECTING THE PROPER EXTENSION CORD
FOR YOUR SAW MODEL
Minimum Gauge Wire
Ampere
Volts AC
Saw Model
Rating
MTD PS 8
110 / 120
1. When using the appliance, an extension cord of ade-
quate size must be used for safety and to prevent loss
of power and overheating.
2. The extension cord must be specifically intended for out-
door use and marked SW-A, SOW-A, STOW-A, SJW-A,
SJOW-A SJTOW-A, SJTW-A, OR SJTW.
12
Length of Power Cord
25 ft. / 7.5m 50 ft. / 15m 100 ft. / 30m
18 Gauge 16 Gauge 14 Gauge
Fig.11