Special Features; Recommended Settings - LRP PULSAR SPORT Manual De Instrucciones

SPECIAL FEATURES

ADJUSTABLE BATTERY CUT-OFF VOLTAGE DURING CHARGE: allows you to fine-tune the
cut-off voltage per cell (TVC = Terminal Voltage during Charge) in a range from 3.80V to 4.37V
in steps of 0.01V.
Changing the LiPo/LiHV battery cut-off voltage from the standard 4.20V/cell (LiPo), 4.35V/cell
(LiHV) has several advantages:
1) Maximize your battery voltage according to the voltage allowed by Technical Inspection.
2) Reduce the maximum punch and power by charging to a lower cut-off voltage than the
standard 4.20V/cell (LiPo), 4.35V/cell (LiHV).
3) Increase the lifetime of your battery by charging to a cut-off voltage lower than 4.20V/
cell (LiPo), 4.35V/cell (LiHV) when maximum performance is not vital, for example during
practice.
4) Charge high-voltage or ‚Outlaw'-LiPo batteries to their specified voltage.
AUTOSTART TIMER: with this handy feature you can select the time that passes until charging
starts automatically. The Autostart timer is adjustable from 0 - 99min. If you stay in the „Auto-
start Display" for longer then 30sec without setting a value, or confirming the charge process,
charging will not start and the charger will go back to the main menu.

RECOMMENDED SETTINGS

Important: always follow the battery manufacturer's recommendations first. The recommendations below should only be seen as a guideline for the most common battery packs!
Charger Voltage / Charge
Battery Type
setting Cells Current
LiPo 1S pack
LiPo 3.7V / 1S
>6000mAh
LiPo 2S pack
LiPo 7.4V / 2S
>6000mAh
LiPo 4S pack 14.8V
LiPo
>6000mAh 4S
LiHV 1S pack
LiHV 3.8V / 1S
>6000mAh
LiHV 2S pack
LiHV 7.6V / 2S
>6000mAh
LiHV 4S pack 15.2V
LiHV
>6000mAh 4S
For any other pack we suggest to charge with 1C charge rate.
Caution: Make sure you always select correct settings (charging mode and pack voltage)!
TROUBLESHOOTING
This product is protected against faults and operator errors by the Multi-Protection-System. Error messages are displayed on the LCD screen and some may interrupt any process to protect
the charger and the battery. The messages are as follows:
LCD MESSAGE POSSIBLE CAUSES -> SOLUTION
Safety timer Charging time-limit setting is reached -> re-adjust if needed
No balancer Balancing not in use -> connect if needed
Pack is balanced Voltage of each cell is even -> pack does not need balancing
Battery full Battery completely full -> does not need charging
Battery Voltage selection not correct >> check for Lixx Cell quantity
Check
No battery connection -> check connection and contacts
connection
Battery defective -> check single cells voltage of battery pack
Voltage not set correctly -> re-adjust cell (pack) voltage
Check Balancer
Wrong battery type selected. Check battery type setting.
REPAIR PROCEDURES / LIMITED WARRANTY
All products from LRP electronic GmbH (hereinafter called "LRP") are manufactured accor-
ding to the highest quality standards. LRP guarantees this product to be free from defects in
materials or workmanship for 90 days (non-european countris only) from the original date of
purchase verified by sales receipt. This limited warranty doesn´t cover defects, which are a
result of misuse, improper maintenance, outside interference or mechanical damage. This
applies among other things on:
• Cut off/changed original input- and/or output-wires
• Mechanical damage of the case
• Humidity/Water inside the case
• Mechanical damage of electronical components/PCB
• Soldered on the PCB
To eliminate all other possibilities or improper handling, first check all other components
in your model and the trouble shooting guide, if available, before you send in this product
for repair. If products are sent in for repair, which do operate perfectly, we have to charge a
service fee according to our pricelist.
Discharge Discharge
D-Peak Trickle
current Voltage
6.0A - - 1.0A 3.3V
6.0A - - 1.0A 6.6V
6.0A - - 1.0A 13.2V
6.0A - - 1.0A 3.3V
6.0A - - 1.0A 6.6V
6.0A - - 1.0A 13.2V
CHANGING THE CURRENT ON THE FLY: The charge current can be changed on the fly by
pressing INC+ or DEC- without interrupting the charging process. This change is not stored.
The next time you start charging, the charger takes the data settings of each charge profile,
stored under "Settings". Keep the buttons pressed to rapidly adjust the current values.
DATA VIEW FUNCTION: during each process you can view additional data by pressing MENU
button. If afterwards no action is made the charger will jump to initial screen automatically after
few seconds. You can also exit this screens manually simply pressing DEC- or INC+ button.
SOFWARE UPDATE: This product's software can be updated via the integrated USB port. For
available updates and information check www.LRP .cc.
USB CHARGE OUTPUT 5V/1.0A: simply plug in your USB device (mobile phone, etc.) with a
suitable cable and charge it directly from your charger.
Charger Voltage / Charge
Battery Type
setting Cells Current
LiPo 2S Rx/Tx pack
LiPo 7.4V / 2S
~2500mAh
LiFe 2S Rx/Tx pack
LiFe 6.6V / 2S
~1600mAh
LiPo 1S Tx pack
LiPo 3.7V / 1S
~3000mAh
NiMH 6.0V Rx pack
NiMH 6.0V / 5
~1600mAh
NiMH 7.2V packs
NiMH 7.2V / 6
<3000mAh
NiMH 7.2V packs
NiMH 7.2V / 6
>3000mAh
LCD MESSAGE POSSIBLE CAUSES -> SOLUTION
Reverse polarity Battery not connected correctly (+/-) -> re-connect with correct polarity
Voltage invalid No voltage on balancer recognized -> check balancer connection
DC input low Input voltage too low (<11.0V on DC input) -> check Input
DC input high Input voltage too high (>18.0V on DC input) -> check Input
Int. temp high Charger overheats -> check for sufficient cooling
Ext. temp. high Battery temperature over the adjusted value -> check setting
High current Internal problem -> re-connect (reset) the charger, load factory settings
Control fail Internal problem -> re-connect (reset) the charger, load factory settings
With sending in this product, the customer has to advise LRP if the product should be repaired
in either case. If there is neither a warranty nor guarantee claim, the inspection of the pro-
duct and the repairs, if necessary, in either case will be charged with a fee at the customers
expense according to our price list. A proof of purchase including date of purchase needs to
be included. Otherwise, no warranty can be granted. For quick repair- and return service, add
your address and detailed description of the malfunction.
If LRP no longer manufactures a returned defective product and we are unable to service it,
we shall provide you with a product that has at least the same value from one of the successor
series.
The specifications like weight, size and others should be seen as guide values. Due to ongoing
technical improvements, which are done in the interest of the product, LRP does not take any
responsibility for the accuracy of these specs.
LRP-Distributor-Service: - check www.lrp.cc
Discharge Discharge
D-Peak Trickle
current Voltage
2.5A - - 1.0A 6.6V
1.6A - - 1.0A 5.2V
3.0A - - 1.0A 3.3V
2.0A 15mV Off 1.0A 4.5V
4.0A 25mV Off 1.0A 5.4V
6.0A 25mV Off 1.0A 5.4V