Shad BC03 Manual Del Usurario página 10

SHAD BC03
INSTRUCTION MANUAL
Welcome
Congratulations and thank you for purchasing a SHAD
BC03 device. Thanks to the intercom function, you
can talk to your passenger, listen to your favourite
music and answer your calls while travelling on your
scooter or motorcycle.
The SHAD BC03 system is compatible with all
Bluetooth devices that transmit audio (mobile
®
phones, smartphones, GPS navigators and other
devices) using the profiles specified in the manual.
It can be paired with any other product in the SHAD
range or to a different Bluetooth
thanks to its UNIVERSAL connectivity feature.
This device is designed so that it may be wholly
integrated into your helmet. It can be operated and
paired
easily through a single control button (1b).
A single red/blue LED indicator (1a) serves to display
connection status, pairing, battery charging and low
battery. The SHAD BC03 device weighs only 55 g.
For better use of the SHAD BC03 device, please read
this manual and keep it in a safe place or find it at
www.SHAD.es
Charging the SHAD BC03
Before using your SHAD BC03 device for the first time,
you must charge the device completely.
Connect the terminal (3) to the provided USB cable (5)
and then connect the cable to a USB charging port.
While charging, the red LED light will switch on (1a) and
it will switch off once charging has been completed.
NOTE: Don't pull on the cable to disconnect it from the USB port
NOTE: As time goes by, batteries gradually lose their
charge. This is why it's important to charge the battery
fully before using the device and allow the battery to
use almost all of it's charge in between charging cycles.
WARNING:
If you plan to store your SHAD device
for a long period of time, be sure to recharge it at
least once every six months to ensure perfect battery
function.
10
Installation
The SHAD BC03 is very easy to install into a helmet.
Remove the side padding from the inside of the helmet
(if it can be removed) and place the devices (2) and
(4) at the height of your ears. The device is designed
so that the main unit with the boom microphone is
placed on the left side, as shown in figure 1, and so
that the second speaker is placed on the right side.
The wire between devices (2) and (4) must be stored
inside the helmet, under the padding. In order to affix
the headphones, two Velcro pads are provided (male
and female) with an adhesive backing (7). In case you
need to use the Velcro, stick the male part of the pad
onto the device and the female part onto the inside of
the helmet.
Depending on the internal configuration of each type of
audio receiver,
®
helmet, it may be necessary to use the entire Velcro pad
or only a part of it (see figure 2). In some cases, it may
only be necessary to stick the male part onto the device
as the inside of the helmet may have padding that can
serve as Velcro (female).
If needed, comfort pads (6) to place on the headphones
are also provided, in order to improve comfort against
your skin.
The charging cable (3) must be placed on the lateral-
back section of the helmet so as to facilitate access to
charge the device.
Place the microphone (1) on the front section of the
helmet (close to and oriented towards your mouth,
always protecting the microphone with the padding).
Linking/Pairing
To use the SHAD BC03, it's necessary to pair it to the
Bluetooth
phone, GPS navigator). While the device is switched off, hold the control button (1b) until the LED indicator
(1a) begins flashing in Red and Blue. The mobile phone
or GPS navigator will find the device under the name
BC03. Select the BC03 device and, if necessary, enter
the access code: 0000. NOTE: Pairing is a process that only needs to be
completed once. When the SHAD BC03 is paired to
a specific device, both devices will pair automatically
when switched off and on.
device you wish to connect it to (mobile
®