Idiomas disponibles
Idiomas disponibles
GAN UHF
Read only
Installation instructions
Ethernet connection
Wiring
- Thread a stripped network cable through the gland.
- Fit the cable with an RJ45 connector.
- Connect the RJ45 connector to the DIGI Connect.
- Connect the power supply to J1.
DIGI default settings
Baud Rate 115200, Data Bits: 8, Parity: None, Stop Bits: 1.
DIGI
STid declares that the GAN-R4x-E reader is compliant with the essential requirements of Directive RED 2014/53/EU and Directive RoHs 2011/65/EU and the Delegated Commission
Directive 2015/863/EU. A copy of our declaration is available on request from [email protected].
This device complies with Part 15 of the FCC rules and with the Innovation, Science and Economic Development Canada's license-exempt RSS(s). Operation is subject to the following
two conditions:
1) This device may not cause harmful interference.
2) This device must accept any interference received, including interference that may cause undesired operation.
Note: the manufacturer is not responsible for any radio or TV interference caused by unauthorized modifications to this equipment. Such modifications could void the user's authority to
operate the equipment.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment generates, uses and can emit radio frequency energy and, if not installed and used in accordance
with the instructions, may cause harmful interference with radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the
interference by taking one or more of the following measures:
-
Reorient or relocate the receiving antenna.
-
Increase the distance between the equipment and receiver.
-
Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for assistance.
This equipment complies with the FCC and ISEDC radiation exposure limits (according to the RSS-102 rules) set forth for an uncontrolled environment under the following conditions:
This equipment is installed and operated such that a minimum separation distance of 25 cm / 9.8 in is maintained between the radiator (antenna) and the user's/nearby
-
person's body at all times.
-
The transmitter is not co-located or operated in conjunction with any other antenna or transmitter.
In accordance with the provisions of the Environment Code, STid finances the collection, decontamination and recycling of WEEE provided by ESR-
RECYLUM, to which STid adheres and to which it has transferred its regulatory responsibilities as a Producer.
STid recommends that owners of used equipment who wish to dispose of it return it as WEEE by contacting ESR / RECYLUM in order to benefit from
the solutions at no additional cost of collecting and recycling used equipment.
More information on
J1
1
GND
2
Power Supply
3
IN
www.recylum.fr
© STid - 20 PA des Pradeaux FR13850 Gréasque - NI1090X07 - Page 3 sur 10 - Ed. 06/05/2019
UHF GAN
Lecture seule
Notice d'installation
Hardware requirements
IEEE 802.3af-compatible PSE (Power Sourcing Equipment).
If several readers are connected to the PSE, check that each
port of the PSE supplies 9W.
Wiring
- Thread a stripped network cable through the gland.
- Fit the cable with an RJ45 connector.
- Connect the RJ45 connector to the DIGI Connect.
DIGI default settings
Baud Rate 115200, Data Bits: 8, Parity: None, Stop Bits: 1.
Note: the IN channel is not available on the PoE model.
Reader Dimensions (mm / in)
Declaration of Compliance
"WEEE Pro" Member
UHF GAN
Solo lectura
Manual de instalación
Ethernet + PoE connection
US
FR
ES
