Tabla de contenido
Idiomas disponibles
Idiomas disponibles
l
INSTALLING lHE HOOD
1.
Before starting the
please check that ali
damaged,
in
such a
tailer and
do
not carry out installation.
Before
the
installation
please remove
the security
see
in
the picture
Furthermore,
please
following
installation
•
Use
an exhausting
length
does
not exceed
•
Limit
the
no. of
since
each
elbow
efficiency
of 1
use no.
2
x 90
ing
l
must not exceed
•
Avoid
abrupt direction
•
Use a 150
mm constant diameter
the whole
length.
•
Use
piping approved
force.
The
manufacturer
any capacity
or
failure to comply
and
the
warranty will be rendered null and
void.
Before making the
2.
are no
structural or other
cabinet, where the appliance is to be
which
could
hinder a proper
Check that
the dimensions
and
the ones
of
with
the
cabinet
be
carried out properly.
3.
Orill
a
790x100 mm rectangular
rear
side
of
the
cook-top for
sion and
a
1090x100 mm
cm version.
In
the version with
ready installed,
remove
suctioning
unit in order
draft in
the hole
made.
In
case
of
the glass
draft in
the
cabinet, making
S-004
appliance installation,
components
case
contact your re-
of
the Oowndraft,
piece
you can
(Fig. 1-2-3-4).
read
carefully
ali of
instructions.
pipe whose
maximum
5
meters.
elbows
in
the piping ,
reduces the
aspiration
linear
meter.
(Ex.
elbows,
the
length of pip-
o
3 meters).
changes.
by standards
will
not
be answerable
noise problems
caused
with
the above instructions
opening,
check that
parts
inside
installation.
of
the
Oowndraft
the
cooktop
are compatible
so
that
the
installation can
hole
the
90 cm ver-
hole
for the 120
the
motor
the screws
and
to
insert
the
version,
insert
the
sure
that
GB
stainless
perfectly to the
case
counter
ing
sealer
are not
draft
edge and
posed
4.
Fix
the special
product
the
lnsert
downdraft
there is a 2
side
net
(Fig.
This distance
sitioned
:
if you
moment of
less steel
work
Before inserting
pipe
for
sure
dicular with
in
5.
In
the
with
for
ing
the
by
either
ing
the
The
back
After
there
ducts.
the
placed,
6.
For
suction unit
and fit
ceed
outside motor
air outlet from
and fit
in
the
al-
the
down-
down-
the
steel
edge
under
cabinet
of
the stainless
steel
frame
in
the hole made,
and then insert the down-
(Fig. 6)
in
the
cabinet
in
such
the
counter
frame
(Fig. 7).
the downdraft
inside the cabinet, using
fixing brackets
8a).
(Fig.
the brackets
in
the
13b),
(Fig.
8b)
mm
distance
of bracket and
the
bottom of
8c).
will
allow the
downwards
of
the
fixing, in
order
trim
perfectly
surface.
the
screws,
that
the appliance is perfectly
the
work surface.
version of
the
Oowndraft equipped
motor,
install
the
motor group adjust-
air evacuation direction as
downwards
or upwards. After
motor,
connect
the
motor can
be
fitted either on the
side
of
the
downdraft.
installing the
motor, connect
(Fig. 1
0).
versions
with
outside
(outside motor)
the
exhaust air
flue as illustrated.
to
fit
the
air outlet
and
the
down draft. Select an
the five possibilities
the
connection provided.
-----1[
the
glass
adheres
surface
In
(Fig. 5).
version,
apply the
using
a
fix-
a way
that
the
are superim-
supplied with
the
lower
side
of
the
in such
a
way
that
between
the
lower
the
cabi-
traction to
be
po-
product, at
the
to
have the stain-
adhering with
the
please
make
perpen-
required,
install-
air
ducts
9).
(Fig.
front
or
the
air
motor,
piace the
in a
suitable area
Pro-
ducts
between
the
(Fig. 11)
17
Capítulos
Tabla de contenido
