Tabla de contenido
Idiomas disponibles
Idiomas disponibles
Treble
Press the treble button on the hardwired controller or wireless remote.
A blue EQ LED will illuminate next to the treble button. When using the
hardwired controller, turn the master volume knob clockwise to
increase the treble and counter-clockwise to decrease the treble.
When using the remote, press and hold "+" button to increase the
treble or press and hold the "–" button to decrease the treble.
An LED will light up and move on the wired controller to indicate
changing treble levels. The LED will reside in the far right position for
maximum treble and in the far left position for minimum treble.
After a few seconds, treble will default back to main volume. To return
to treble control, press the treble button again.
Stand-by
To mute the FX6021 press the stand-by button on the hardwired
controller or wireless remote. The blue LED located next to the power
button
will turn off. To un-mute, press the stand-by button again.
It is important to note that while in stand-by mode the system
continues to receive power. To completely shut down the FX6021, press
the standby button
on the hardwired controller or wireless remote
and then unplug the unit from the wall.
System Specifications
Sound Pressure Level (SPL): 105 dB
Total Continuous Power:
Front Speakers:
Subwoofer:
System Response:
Signal to Noise Ratio
@ 1 kHz input:
Driver (per Satellite):
Troubleshooting
Symptom
Possible Problem
Can' t insert
Some of the pins are bent.
the wired
controller's DIN
connector into
the subwoofer.
No LEDs are lit.
Power isn' t turned on.
Power adapter isn' t connected to the wall outlet
and subwoofer.
Surge protector (if used) isn' t powered on.
Wired controller isn' t connected to the subwoofer.
Wall outlet not functioning.
Controller
DIN connector not inserted in subwoofer jack.
doesn' t work.
75 Watts RMS
12.5 Watts/channel @ 4 ohms @ 10% THD
@ 180 – 15000 Hz 2 Channels Loaded
50 Watts @ 4 ohms @ 10% THD
@ 40 – 180 Hz Single Channel Loaded
32 Hz – 18 kHz (-10dB)
> 75 dB
Six 1" full-range micro drivers
Headphones
To use headphones with the system, plug them into the labeled
jack on the side of the wired controller. When headphones are
connected, both satellites and the subwoofer are muted.
WALL MOUNTING
Remove the satellite base from the satellite. The satellite can be
mounted to the wall using the key holes (top and bottom), or by using
the threaded inserts on the rear of the satellite (threaded inserts
require the purchase of a universal mounting kit.)
SUBWOOFER
Driver:
One 6.5" long-throw woofer
POWER REQUIREMENTS
USA, Canada and applicable
Latin American countries:
Europe, United Kingdom,
applicable Asian countries,
Argentina, Chile and Uruguay:
ETL/cETL/CE/NOM Approved
Solution
Try to gently straighten the pins with tweezers or very small pliers. If this does
not work, contact the Altec Lansing Consumer Support Department for further
instructions.
Press the Power button on the wired controller or remote control.
Disconnect and then reconnect the power adapter to both the wall outlet and
the subwoofer.
If the power adapter is plugged into a surge protector, make sure the surge
protector is switched on.
Connect the wired controller to the subwoofer.
Plug another device into the same jack on the wall outlet to ensure the outlet
is working.
Verify that the grey-colored DIN connector is firmly inserted into the DIN
connector jack on the subwoofer. Ensure the pins are aligned between the
plug and jack. Remember, the arrow should be facing up.
3
120 V AC @ 60 Hz
230 V AC @ 50 Hz
Tabla de contenido
