Tabla de contenido
Idiomas disponibles
Idiomas disponibles
Enlaces rápidos
Ford Data Interface with SWC Control 2007-up
• Provides accessory power (12-volt 10-amp)
• Retains R.A.P. (retained accessory power)
• Provides NAV outputs (parking brake, reverse, and
speed sense)
• Retains audio controls on the steering wheel
• BX-FD2 interface
• BX-FD2 harness
• 16-pin harness with stripped leads
• Female 3.5mm adapter with Brown and Brown/White wires
Axxess Integrate
Installation instructions for BX-FD2
BX-FD2
FEATURES
• High level speaker input
• Can be used in non-amplified systems, amplified
systems, and Sony/THX amplified systems
• Micro "B" USB updatable
INTERFACE COMPONENTS
APPLICATIONS
See inside front cover
axxessinterfaces.com
Connections to be made ........................................... 2-4
Initializing the BX-FD2..................................................5
Adjusting the BX-FD2 ...................................................5
Extra Features ...............................................................5
Steering wheel audio control extra settings ...............5
TOOLS REQUIRED
• Wire cutter • Crimp tool • Solder gun • Tape
• Connectors (example: butt-connectors, bell caps, etc.)
CAUTION!
tery terminal before beginning any installation, unless the vehicle
manufacturer recommends against so. Please check with your local
Dealership for more information. All accessories, switches, climate
controls panels, and especially air bag indicator lights must be con-
nected before reconnecting the battery or cycling the ignition. Also,
do not remove the factory radio with the key in the on position, or the
vehicle running. It would be best to remove the key from the ignition
and then wait a few seconds before removing the factory radio.
•
metraonline.com
Table of Contents
L.E.D. feedback .........................................................5
Changing radio type .................................................7
Resetting the BX-FD2 .............................................10
Metra recommends disconnecting the negative bat-
© COPYRIGHT 2004-2015 METRA ELECTRONICS CORPORATION
Tabla de contenido
Manuales relacionados para Axxess BX-FD2
Resumen de contenidos para Axxess BX-FD2
-
Página 1: Tabla De Contenido
Installation instructions for BX-FD2 Table of Contents BX-FD2 Ford Data Interface with SWC Control 2007-up Connections to be made ........... 2-4 Initializing the BX-FD2..........5 Adjusting the BX-FD2 ...........5 Extra Features ...............5 FEATURES Steering wheel audio control extra settings ....5 L.E.D. feedback ............5 • Provides accessory power (12-volt 10-amp) -
Página 2: Important Warning
BX-FD2 Applications Connections to be made FORD LINCOLN From the 16-pin harness with stripped leads to the Edge 2007-2010 MKX 2007-2010 aftermarket radio: Escape 2008-2012 MKZ 2007-2009 • Connect the (2) Red wires to the accessory wire. Expedition 2007-2014 Navigator 2007-2014 F-150 (with CD player) 2009-2012 MAzDA Note: If installing the AX-LCD (sold separately), there will be an accessory wire... - Página 3 Note: If this jack is not present on the aftermarket radio, just leave be. Only the center channel speaker will be lost. • Connect the Light Green wire to the parking brake wire (if applicable). • Connect the Blue/Pink wire to the VSS/speed sense wire (if applicable). • Disregard the RCA jack labeled “SUBWOOFER”, it will not be used in this application. From the BX-FD2 harness to the aftermarket radio: For models without SyNC: • Connect the Red RCA jack labeled “FROM 3.5” to the right AUX-In jack. • Connect the Black wire to the ground wire. • Connect the White RCA jack labeled “FROM 3.5” to the left AUX-IN jack.
- Página 4 • Parrot Asteroid Smart or Tablet: Connect the 3.5mm jack with Brown and Brown/White wires, onto the male 3.5mm SWC jack of the BX-FD2. Any remaining wires, tape off and disregard: into the AX-SWC-PARROT (sold separately), and then connect the 4-pin connector from the AX-SWC-PARROT into the radio. • Eclipse: Connect the steering wheel control wire, normally Note: The radio must be updated to rev. 2.1.4 or higher software. Brown, to the Brown/White wire of the adapter. Then connect the remaining steering wheel control wire, normally Brown/White, • For all other radios: Connect the 3.5mm jack of the BX-FD2 to the Brown wire of the adapter. into the jack on the aftermarket radio designated for an external steering wheel control interface. Please refer to the aftermarket • Metra OE: Connect the steering wheel control Key 1 wire (Gray) radios manual if in doubt as to where the 3.5mm jack goes to. to the Brown wire. • Kenwood or select JVC with a steering wheel control wire: Connect the Blue/yellow wire to the Brown wire.
-
Página 5: Initializing The Bx-Fd2
BX-FD2 Extra features Initializing the BX-FD2 SyNC, rear seat entertainment (RSE), satellite radio (SAT), and AuX-IN: • Turn the key to ignition, the L.E.D. inside the interface by the 16-pin harness will turn on solid Red. • If your vehicle comes equipped with SYNC, RSE, SAT, or AUX-IN, the BX-FD2 can retain these features. • After 30 seconds the L.E.D. will turn off for a few seconds, and then flash up to 16 times depending on what radio it sees connected to it, and then turn off Note: Most Ford radios have SAT built into the factory radio, so this feature is lost if so. -
Página 6: Steering Wheel Audio Control Extra Settings
* Note: If the BX-FD2 flashes (7) times, and you do not have an Alpine radio connected to it, that means the BX-FD2 does not detect a radio connected it. Verify that the 3.5mm jack is connected to the correct steering wheel jack/wire in the radio. -
Página 7: Changing Radio Type
BX-FD2 Steering wheel audio control extra settings Attention: The Axxess Updater App can also be used to program the following (3) sub-sections as well, pending that the interface has been initialized and programmed. Radio legend Changing radio type 1. Eclipse (Type 1) 9. Valor If the LED flashes do not match the radio you have connected, you must manually program the BX-FD2 to tell it what radio it is connected to. -
Página 8: Remapping The Steering Wheel Control Buttons
Note: Not all radios will have all of these commands. Please refer to the owner’s “Volume-Up”. This will tell the BX-FD2 that this function is not available and manual provided with the radio, or contact the radio vendor directly for specific it will move on to the next function. -
Página 9: Dual Assignment Instructions (Long Button Press)
BX-FD2 Steering wheel audio control extra settings Dual assignment instructions (long button press) Dual assignment legend The BX-FD2 has the capability to assign (2) functions to a single button (except 1. Not allowed 9. Power 16. Fan-Down (not applicable in this “Volume-Up” and “Volume-Down”). Follow the steps below to program the 2. Not allowed 10. Band application) button(s) to your liking. 3. Seek-Up/Next 11. Play/Enter 17. Temp-Up Note: “Seek-Up” and “Seek-Down” come pre-programmed as “Preset-Up” and (not applicable in this “Preset-Down”... -
Página 10: Resetting The Bx-Fd2
BX-FD2 Steering wheel audio control extra settings Resetting the BX-FD2 1. With the radio on, turn the potentiometer: Note: Before proceeding, remember the position the potentiometer is at. Left..hold for 2 seconds Right..hold for 2 seconds Left..hold for 2 seconds Back to the initial position 2. The L.E.D. in the BX-FD2 will flash fast, and then flash slowly up to (16) times. Pay close attention as to how many slow flashes there are. This will help in troubleshooting, if need be. - Página 11 BX-FD2 Notes...
-
Página 12: Important
Installation instructions for BX-FD2 IMPORTANT If you are having difficulties with the installation of this product, please call our Tech Support line at 1-800-253-TECH. Before doing so, look over the instructions a second time, and make sure the installation was performed exactly as the instructions are stated. Please have the vehicle apart and ready to perform troubleshooting steps before calling. NOWLEDGE IS OWER Enhance your installation and fabrication skills by enrolling in the most recognized and respected mobile electronics school in our industry. Log onto www.installerinstitute.com or call 800-354-6782 for more information and take steps toward a better tomorrow. -
Página 13: Interfase De Datos Ford Con Control Swc 2007-Up
Instrucciones de instalación para BX-FD2 Indice BX-FD2 Interfase de datos Ford con control SWC Conexiones que se deben hacer ......2-4 Inicialización del BX-FD2 ..........5 2007-up Ajuste del BX-FD2 ............5 Características adicionales ..........5 CARACTERÍSTICAS Configuraciones adicionales de control del audio del volante ...........5 •... -
Página 14: Advertencia Importante
BX-FD2 Aplicaciones Conexiones que se deben hacer FoRD LINCoLN Arnés de 16 pins con conectores pelados al radio de Edge 2007-2010 2007-2010 mercado secundario: Escape 2008-2012 2007-2009 • Conecte los (2) cables rojos al cable de accesorios. Expedition 2007-2014 Navigator... - Página 15 • Conecte el cable azul/rosa al cable VSS o del sensor de velocidad (si aplica). • Ignore el conector RCA rotulado “SUBWOOFER”, ya que no se utilizará en esta aplicación . Del arnés BX-FD2 al radio de mercado secundario: Para modelos sin SyNC: •...
- Página 16 • Parrot Asteroid Smart o Tablet: Conecte el conector de SWC de 3.5 mm del BX-FD2. Cualquier cable restante debe cubrirse con 3.5mm al AX-SWC-PARROT (se vende por separado), y cinta e ignorarse: después conecte el conector de 4 pins del AX-SWC-PARROT...
-
Página 17: Inicialización Del Bx-Fd2
SyNC, entretenimiento en asiento trasero (RSE), radio satelital (SAT) y AuX-IN: de 16 pins, se encenderá en rojo sin parpadear. • Si su vehículo está equipado con SYNC, RSE, SAT o AUX-IN, el BX-FD2 puede conservar • Después de 30 segundos el L.E.D. se apagará unos pocos segundos, y después estas funciones. -
Página 18: Configuraciones Adicionales De Control Del Audio Del Volante
El 16a parpadeo del foco L.E.D. es para Philips * Nota: Si el BX-FD2 parpadea (7) veces y no tiene un radio Alpine conectado a él, esto significa que el BX-FD2 no detectó ningún radio conectado. Verifique que el conector de 3.5mm esté... - Página 19 BX-FD2 Configuraciones adicionales de control del audio del volante Atención: La aplicación Axxess Updater también se puede usar para programar las siguientes (3) subsecciones también, hasta en tanto la interfase se haya inicializado y programado. Leyenda del radio Cambio de tipo de radio Si el parpadeo del foco LED no corresponde al radio que tiene conectado, debe 1.
- Página 20 3. Buscar siguiente (no aplica) 4. Buscar anterior 1) Asegúrese que el BX-FD2 esté visible para que se pueda ver el parpadeo del 13. Colgado (no aplica) foco L.E.D. para confirmar el reconocimiento de los botones. 5. Fuente/Modo 14.
- Página 21 Configuraciones adicionales de control del audio del volante Asignación dual de instrucciones (presión de botones por largo tiempo) Leyenda asignación dual El BX-FD2 tiene la capacidad de asignar (2) funciones a un solo botón (excepto 1. No se permite 12. PTT “Subir volumen”...
- Página 22 Izquierda..mantenga presionado durante 2 segundos Vuelta a la posición inicial 2. El L.E.D. del BX-FD2 parpadeará rápido, y después parpadeará lentamente hasta 16 veces. Ponga atención al número de parpadeos lentos que hay. Esto le ayudará en la resolución de problemas, si es necesario.
- Página 23 BX-FD2 Notas...
-
Página 24: Importante
Instrucciones de instalación para BX-FD2 IMPoRTANTE Si tiene dificultades con la instalación de este producto, llame a nuestra línea de soporte técnico al 1-800-253-TECH. Antes de hacerlo, revise las instrucciones por segunda vez y asegúrese de que la instalación se haya realizado exactamente como se indica en las instrucciones.