Fuse Check/Replacement; Safety Functions And Troubleshooting; Safety Functions - Kent Euroclean Razor 17B Instrucciones De Uso

INSTRUCTION MANUAL FOR USE AND MAINTENANCE
REMARK:
When the battery charger is connected
to the electrical system, all machine
functions are automatically cut off.
When the red warning light (4, Fig. B) on
the control panel turns on, it shows that
the battery charger is charging the bat-
teries.
3. When the red warning light (4, Fig. B) turns off, the
battery charging is completed.
4. Once the battery
disconnect the battery charger plug (22, Fig. C)
from the electric system and hook it to its housing
on the machine.
5. Carefully lower the tank assembly (19, Fig. H) by
means of the manoeuver handle (2, Fig. C).
6. Remove the key (24, Fig. C) from its housing and
remove the tank assembly fastening screw (1, Fig.
H).
7. Now the machine is ready to be used.
REMARK:
For further information about the bat-
tery charger operation (16, Fig. H), see
the related Manual.

FUSE CHECK/REPLACEMENT

1. Disconnect the battery connector (25, Fig. C ).
2. Drain the water from the tanks (5 and 6, Fig. H) by
means of the hoses (17 and 18, Fig. C).
3. Remove the key (24, Fig. C) from its housing and
remove the tank assembly fastening screw (1, Fig.
H).
4. Carefully lift the tank assembly (19, Fig. H) by
means of the manoeuver handle (2, Fig. C).
5. 20BT versions only: loosen the screws (10, Fig.
G) and remove the cover (11).
6. 20BT versions only: check/replace the fuses:
– traction fuse (30A): (8, Fig. G)
– electronic board protection fuse (2A): (9, Fig.
G).
7. 20BT versions only: loosen the wing nuts (12, Fig.
G) and move to one side the support with the
traction electronic board (13, Fig. G).
8. Unscrew the screws (4, Fig. G) and carefully
remove the electric component box cover (5)
making it slide upwards.
9. Check/replace the fuses:
– Brush safety fuse (50 A): (1, Fig. G)
– Aspirator fuse (40 A): (2, Fig. G)
– Solenoid valve fuse (5 A): (3, Fig. G)
10. Install in the reverse order of removal.
14
charging is completed,
SAFETY FUNCTIONS AND
TROUBLESHOOTING

SAFETY FUNCTIONS

The red connector (25, Fig. C) can be used in case of
emergency to stop all the machine functions. If neces-
sary, remove the connector by means of the red hand-
le.
TROUBLESHOOTING
TROUBLE
Motors do not work: no warning
light turns on
The aspirator motor does not
start
Insufficient dirty water suction
Insufficient detergent flux to the
brush
Squeegee-provoked lining
The traction does not operate
(*)
(*):20BT versions only
REMARK:
In case of battery charger malfunction,
contact the Kent/Euroclean Service Cent-
er.
POSSIBLE CAUSE
Disconnected battery connector (25,
Fig.C)
Completely discharged batteries
Burnt fuse
Full recovery tank (5, Fig. H)
Obstructed suction grid (8, Fig. H) or
stuck closed float
Disconnected hose (26, Fig. C) from
the squeegee
Dirty squeegee or worn or damaged
squeegee blades
Incorrectly closed tank cover, or
damaged gasket (7, Fig. E) or
obstructed compensation hole (11,
Fig. E)
Dirty detergent filter (2, Fig. F)
Dirty tank (6, Fig. H) (obstructed
output hole)
Debris under the squeegee blades
Worn, chipped or torn squeegee
blades
Not handwheel-balanced squeegee
(12, Fig. C)
Disconnected battery connector (25,
Fig. C)
Key (9, Fig. B) positioned to "0"
Speed governor (11, Fig. B) is turned
completely counterclockwise
Blown traction fuse (8, Fig. G)
Electronic board malfunction due to
overload or overheat; wait at least 5
minutes before resetting the system
by turning the key (9, Fig. B)
08812946(3)2003-08