Maintenance And Cleaning; Ordering Spare Parts; Waste Disposal - EINHELL NHT 2000 Manual De Instrucciones Original

Anleitung_NHT_2000_SPK7:_
GB
6.3 Adjusting the heat output
If the heater is switched on, use the left hand push
button first(10). If the appliance heats with 1000 W,
the LCD display shows a symbol ("Flame") as a sign
of low heat output. Press the right hand push button
(9). If the appliance heats with 2000 W, the LCD
display shows a different symbol as a sign of high
heat output. To reduce the heat output press the right
hand push button (9) again, to completely switch off
the heat output, press the left hand push button (10)
The ventilator keeps running without heat output. To
switch the ventilator OFF completely press the push
button "ON/OFF"(4). The ventilator keeps running
warm for approximately 30 seconds afterwards and
then switches off automatically.
6.4 Set the ideal room temperature
(Range 14°C - 34°C)
In order to set the ideal temperature, press the push
button "Temp+"(5) or "Temp-" (6). The set
temperature appears on the display. As soon as the
temperature in the integrated temperature sensor in
the appliance has been reached, the heating
switches off and only switches itself back on when the
temperature goes below the ideal temperature.
6.5 Switching on the oscillation function
Press the push button "(7)" The appliance swivels 35°
to the left and 35° to the right. To switch off the
"oscillation" function and have the appliance blow in
one specific direction only, press the "oscillation"
pushbutton again.
6.6 Automatic turn-off time (Range 1 - 12h)
Press the pushbutton "Timer"(8) when the appliance
is switched on. The clock symbol appears on the
display. When this flashes, the automatic turn-off time
can be set by pressing the buttons "Temp+" (5) or
"Temp-" (6). The appliance switches off automatically
after the set time has expired.
6.7 Overheating guard
In case of excessive heating, the appliance switches
automatically. Should this occur, set the mains
voltage switch (12) to "0" and pull out the power plug.
Allow the appliance to cool down for about 15
minutes. After eliminating the cause (e.g. a covered
air grille), the appliance can be switched on again as
described in 6.1. If the appliance is not sufficiently
cooled off , it will not allow itself to be switched on. If
the overheating guard triggers repeatedly, please
contact your customer service centre (in Germany
ISC GmbH).
10
15.06.2009 15:14 Uhr Seite 10
6.8 Topple cut-out
If the appliance is tipped over during operation, it will
be switched off automatically by the switch (11). The
LCD display and the operating status indicator will no
longer be lit. After setting up the appliance (switch at
position 11 must be depressed) the appliance stays
off and must be switched on again with the push
button (4) as described under 6.2.

7. Maintenance and cleaning

Before carrying out any cleaning and
maintenance work the appliance must be turned
off, disconnected from the power supply and
cooled down.
Maintenance and repair work may only be carried
out by an authorized electrical servicing
contractor or ISC GmbH.
Check the mains lead at regular intervals for
signs of defects or damage. A damaged mains
lead may only be replaced by an electrician or
ISC GmbH in compliance with the relevant
regulations.
Use a slightly damp cloth to clean the casing.
8. Storage
The heater should be stored in a dry place, covered if
possible.

9. Ordering spare parts

Please provide the following information on all orders
for spare parts:
Model/type of the appliance
Article number of the appliance
ID number of the appliance
Part number of the required replacement part
Current prices and information are available at
www.isc-gmbh.info

10. Waste disposal

Appliance, accessories and packaging should be
recycled in an environmentally friendly manner.
Plastic parts are coded for purposes of separation
when recycling.