Sears 358.799211 Manual Del Usuario página 20

H. TROUBLE SHOOTING CHART
SYMPTOM CAUSE
Engine will not
start or will run
only for a few
seconds after
starting.
Engine will not
idle properly,
Engine wii! not
accelerate,lacks
power, or dies
under a load.
Engine
smokes
excessively.
Engine runs hot.
Cut.gilead tops
under a load or does
not turn when en-
gine is accelerated,
Line does not
advance or breaks
while cutting.
,,LJ
Line welds onto sl_ool,
LinepJl beck .............
into head.
!, Fuel tank empty,
2. Engine flooded,
3, Spark plug not firing,
4, FueI not reaching carburetor.
5. Carburetor requires adjustment.
6. None of the above.
........m..
1, Carburetor set too fast or too slow,
2. Carburetor requires adjustment.
3. None of the above.
I, Air filter
2. Spark plug fouled.
3. Carburetor requires adjustment,
4. Muffler outlets plugged.
5. None of the above.
1, Air filter dirty,
2. Fuel mixture incorrect.
3. Carburetor requires adjustment,
1, Fuel mixture incorrect.
2. Spark plug incorrect.
3. Carburetor set too low (Lean).
4, None of the above,
1, Drive S_aft not engaged,
2. Carburetor requires adjustments,
3. Drive shaft broken.
,,,,,,,,,, , ,,,.,. ,
1, Line hnproperly routed _ head.
2. Line improperly wound onto spool.
3. Line size incorrect.
4. Old cutting line,
5. Too little line outside head,
6. Dirt accumulated on cover cut-outs.
1, Line size incorrect,
2. OId cutting line.
3. Incorrect spool,
4. Crowding line against material being cut.
5. Cutting at higher speed than necessary, .........
I, Too little line outside of head.
2. Old cutting line,
REMEDY
1. Fill tank with correct fuel mixture
2. See "Starting Instructions. _
3. Install new plug/check ignition system.
4. Clean fuel filter; inspect fuel line.
5. See _Carburetor
Adjustments."
6. Conta_ _our SEARS Serv:i'ce Center/Dept.
1. See "Carburetor Adjustments."
2. See "Carburetor Adjustments."
3. Contact your SEARS Service Center!Dept.
1. Clean or replace air filter.
2. Clean or replace spark plug and re-gap.
3. See "Carburetor Adjustments. _
4. Contact your SEARS Service Center/Dept.
5. Contact your SEARS Service Center/Dept.
1. Clean or replace air filter.
2. Refuel with correct fuel mixture.
3. See "Carburetor Adjustments. _
1. See "Fueling Your Unit."
2. Replace with correct plug.
3, See "Carburetor Adjustments,"
4.Contact_rour SEAl,S ServiceCenter/Dept.
1.See "Assembly," "Tube."
2.See _Carburetor Adjustments."
3.Contactyour SEAB_ ServiceCenter/Dept.
,,,,,,,,,,,,, _ .......,
1. Remove coven Check line routing.
2, Rewind line tightly and evenly.
3. Use only ,080" diameter line.
4. Replace with new cutting line.
5. Remove coven Pull 4" of line to outside.
6. Clean cover cut-outs.
1. Use only .080" diameter line.
2. Replace with new cutting line.
3o Use proper spool.
4. Cut with tip of line.
5. Reduce cutting speeck
....
1:Remove coven Puff4" °flin e t°outside.
2.Replacewith new cutting line.
IIII IIII II IIIIIIIIIIll IIIIIIIIIIIII I I I IIIIIWIH_[ [ liHi IIIIIIII I
, ..Ji r • i ii. • i i illllllllllllll IrIH II I Illlllllllll IH I I
ACCESSORIES
, _ mm irl ii I i iii i iii I r HH
ITEM STOCK NO.
SAFETY GOGGLES . .... 71-85707
SEARS 2-CYCLE ENGINE OIL
--3.2 oz ............................................................................. 71-36552 .
--8 oz ............................................................................... 71-36555
- - t6 oz .............................................................................. 71-36553
REPLACEMENT TRIMMER HEAD ....................................................... 71-85801
SPOOL W/_INE .......................................................................... 71-85811
NYLON CUTTING LINE
80 Ft. (.080 Dia.) Cutting Line .......................................................... 71-85773
200 Ft, (,080 Dim) Cutting Line .......................................... •.............. 71-85608
400 Ft. (.080 Dial) Cutting Line ........................................................ 71-85778
SPARK PLUG ........................................................................... 71-85854
AIR FILTER ............................................................................ 530-037331
FLEX SHAFT LUBE ..................................................................... 952-030139
- 20 -