Important Safety Information; Connection Considerations; Mounting Location Considerations; Fusion ™ Sg-Vregled And Ms-Vreg12 Installation Instructions - Fusion SG-VREGLED Instrucciones De Instalación

Fusion ™ SG-VREGLED and MS-
VREG12 Installation Instructions

Important Safety Information

Failure to follow these warnings and cautions could result in
personal injury, damage to the vessel, or poor product
performance.
See the Important Safety and Product Information guide in the
product box for product warnings and other important
information.
This device must be installed according to these instructions.
Disconnect the vessel's power supply before beginning to install
this product.
Before applying power to this product, make sure it has been
correctly grounded, following the instructions in the guide.
Always wear safety goggles, ear protection, and a dust mask
when drilling, cutting, or sanding.
When drilling or cutting, always check what is on the opposite
side of the surface.
You must read all installation instructions before beginning the
installation. If you experience difficulty during the installation,
contact Fusion Product Support.
™
What's in the Box
• 1 voltage regulator
• 1 removable terminal block connector
• 2 mounting screws
About the Voltage Regulator
Depending on the model, this device either converts the voltage
from your boat battery to a steady 12 Vdc (MS-VREG12), or it
regulates the voltage from your battery to power the LEDs on
compatible Fusion speakers (SG-VREGLED). The SG-
VREGLED model also allows you to set the LEDs to dim with
the boat lights and to select the color of the LEDs.

Mounting Location Considerations

If you are mounting the bracket on fiberglass with screws, it is
recommended to use a countersink bit to drill a clearance
counterbore through only the top gel-coat layer. This will help to
avoid any cracking in the gel-coat layer when the screws are
tightened.
Stainless-steel screws may bind when screwed into fiberglass
and overtightened. Garmin
lubricant to the screws before installing them.
When selecting a mounting location for the device, observe
these considerations.
• Due to the water rating, this device must be mounted and the
wiring connections must be made in a non-submerged
location, and it should not be exposed to spray or wash
down.
• The device should be mounted with the terminal block facing
downward, to avoid water entering the device through the
connector port.
• The best location for the device is near the battery, in a
protected area.
2
WARNING
CAUTION
NOTICE
NOTICE
recommends applying an anti-seize
®

Connection Considerations

The 12 Vdc wiring from the battery to the regulator must run
through a fuse near the power supply using a 5 A fuse (not
included). You must connect the red power (+) wire to the fuse.
The red power (+) wire should also connect to an isolator switch
or circuit breaker to turn the regulator on and off. If the regulator
is used as an accessory with a stereo, you can use the same
isolator or circuit breaker that controls the power supply to the
stereo. This allows the regulator and the stereo to turn on and
off at the same time.
Wire Extensions
To ensure proper functionality of the voltage regulator, you
should use the wire gauge recommended for the wire function.
NOTE: The wire sizes provided in the following tables are valid
for a maximum length of 6 m (20 ft.). If a longer extension is
needed, contact Fusion Product Support for assistance.
SG-VREGLED
Wire Function
The power and ground wires from the boat battery. 18 AWG (0.8 mm
The LED power cables to each speaker.
The REMOTE ON input wire and the DIM INPUT
wire.
MS-VREG12
Wire Function
All power and ground wires from the boat battery,
and all wires to the regulated device.
Installing the SG-VREGLED Voltage Regulator
Before you permanently install the voltage regulator, you should
select a mounting location, make wiring connections, and test
the wiring connections.
1
After you have selected a mounting location for the regulator,
route the appropriate cables to the mounting location.
2
Use a flat-blade screwdriver to connect the detachable
connector on the regulator, based on the diagram and table.
TIP: You can disconnect the connector from the regulator to
access the binding posts more easily.
Item Description
REMOTE ON You can connect to the stereo "Amplifier On"
output to turn the regulator on and off with your
stereo.
You can connect to an isolator switch for
manually-switched operation.
You can connect to + 12V IN for permanent
operation.
+ 12V IN The positive wire from the boat battery.
This wire must be connected through a 5 A fuse
(not included) near the power supply.
GROUND IN The negative or ground wire from the boat
battery.
NOTICE
Minimum Gauge
20 AWG (0.5 mm
22 AWG (0.3 mm
Minimum Gauge
18 AWG (0.8 mm
Installation Instructions
2
)
2
)
2
)
2
)