Setting Up Your Dvd Player; Preparing The Remote Control; Connecting Ac Power; Connecting Dc Power - Insignia NS-MDDVD10 Guia Del Usuario

Insignia NS-MDDVD10 Dual-Screen Portable DVD Player
Number Remote control
15 Angle button
16 Audio button
17 Subtitle/Return button

Setting up your DVD player

Preparing the remote control

Installing remote control battery
Warning Do not throw the battery into fire. Dispose
of used batteries as hazardous waste.
Do not drop or disassemble the remote
Caution
control. Do not get the remote control wet.
To install the battery in the remote control:
1 Remove the battery holder.
2 Insert one CR2025 (3-volt) battery into the
battery compartment. Make sure that the +/–
symbols on the battery match the +/– marks
shown on the battery holder.
3 Slide the battery cover into the remote
control.
4 Remove the PVC sheet before operating the
remote control.
5 Point the remote control at the remote sensor
on the DVD player. The effective distance for
remote operation is about 16 feet (5 meters).
Note:
When the remote control will not be used for a long period of
time or when the battery is worn out, remove the battery to
prevent leakage.
Note:
When using the remote control and you are required to move
closer to the stereo for the remote control to operate, replace
the battery. The remote control may not operate correctly if
direct sunlight or the light of a high-frequency fluorescent
lamp enters the remote control light sensor. In this case,
change the system installation position to prevent the
problem.
Function
Switch between multiple
camera angles when the
DVD playing has multiple
camera angles recorded.
Select one audio sound
tracks programmed on a
DVD or select audio output
mode on an AUDIO CD.
Select one of the subtitle
languages programmed on a
DVD or return to the normal
operation after using the
SETUP menu of a DVD.
www.insignia-products.com

Connecting AC power

The AC adapter operates using AC power
between 100 and 240 volts.
Note:
Before operating the DVD player in a new area for the first
time, you must check that the operating voltage of your DVD
player is identical to the voltage of your local power supply.
This DVD player is to be operated only at the power source
voltage printed on the back panel. Disconnect from the
power outlet when not in use for a long period of time.
To connect the AC adapter:
Built-in DIN cable
Power indicator
AC power cord
on AC adapter
1 Connect the built-in DIN cable from the
bottom of the monitor to the Main Unit port
on the DVD player.
2 Connect the plug end of the AC adapter to
the DC In 9V/Car Plug - 12V jack on the DVD
player.
3 Connect the AC power cord to the
AC adapter.
4 Connect the AC power cord to an AC outlet.
When the power cord is connected to the AC
outlet, the power indicator will be on even if
the DVD player is turned off.

Connecting DC power

The car power adapter operates in vehicles with
a 12-volt, negative-ground electrical system.
Warning Disconnect the car power adapter when not in
use.
Do not use this system in vehicles with 24-volt
systems.
Caution • Use this unit only with the included car
power adapter. Using another car adapter
could damage the unit or your vehicle.
• The 12V car power adapter included is for
use with this unit only. Do not use it with
any other equipment.
• In the interest of traffic safety, drivers
should not operate the unit or view videos
while driving.
• When the inside of the cigarette lighter
socket is dirty with ashes or dust, the
power section may become hot due to
poor contact. Be sure to clean the
cigarette lighter socket before use.
• After use, disconnect the car power
adapter from both the unit and cigarette
lighter socket.
• If the unit is not properly attached to a
vehicle, it may become airborne in the
event of an accident and cause damage,
injury, or death.
• Check local traffic laws for rules
governing use of video devices in vehicles
before using this unit in your vehicle.
7