Tabla De Contenido - Adam Equipment PMB 53 Manual Del Operador

1.0 CONTENTS
1.0 CONTENTS ........................................................................................................................... 1
2.0 INTRODUCTION .................................................................................................................... 3
3.0 SET UP .................................................................................................................................. 5
3.1 UNPACKING AND SETTING UP YOUR ANALYZER .................................................................................... 5
3.2 ASSEMBLING THE ANALYZER .................................................................................................................... 6
3.3 LEVELLING THE ANALYZER ........................................................................................................................ 7
3.4 WARM-UP TIME ............................................................................................................................................ 7
3.5 LOCATING AND PROTECTING YOUR ANALYZER ..................................................................................... 8
3.6 SAFETY ......................................................................................................................................................... 9
4.0 DISPLAY and KEYPAD ...................................................................................................... 12
4.1 NUMERIC ENTRY METHOD ....................................................................................................................... 14
5.0 REAR PANEL INTERFACES .............................................................................................. 15
5.1 POWER ........................................................................................................................................................ 15
5.2 DATA INTERFACES .................................................................................................................................... 15
5.2.1 FILES ON A USB MEMORY DEVICE ............................................................................................ 16
5.3 SECURITY LOCK ........................................................................................................................................ 17
6.1 SETUP OF METHOD ................................................................................................................................... 18 6.1.1 MANUALLY SETTING TEST PROCEDURES ................................................................................. 21
6.1.2 PRINT CURRENT SETTINGS ......................................................................................................... 26
6.2 STORE TEST SETTINGS ........................................................................................................................... 27
6.3 RECALL TEST SETTINGS .......................................................................................................................... 28
6.4 DELETE TEST SETTINGS .......................................................................................................................... 29
6.5 REVIEW TEST SETTINGS ......................................................................................................................... 29
6.6 STORE and RECALLING TEST SETTINGS FROM USB MEMORY ........................................................... 29
7.0 RUNNING A TEST ............................................................................................................... 33
8.0 PRINT AND STORE RESULTS ........................................................................................... 37
8.1 PRINTING FINAL TEST RESULTS ............................................................................................................. 37
8.2 STORING TEST RESULTS ......................................................................................................................... 37
8.3 RECALLING TEST RESULTS ................................................................................................................... 38
8.4 DELETING TEST RESULTS ...................................................................................................................... 38
9.0 STORING RESULTS IN USB MEMORY ............................................................................. 40
10.0 ANALYZER MENUS ............................................................................................................ 42
10.1 SUPERVISOR MENUS ................................................................................................................................ 42
10.1.1 SERIAL INTERFACE PARAMETERS ............................................................................................. 44
10.1.2 SETUP PARAMETERS ................................................................................................................... 45
10.1.3 CALIBRATION ................................................................................................................................. 47
10.1.3.1 MASS CALIBRATION ..................................................................................................................... 47
10.1.3.2 TEMPERATURE CALIBRATION ..................................................................................................... 48
10.1.3.3 CALIBRATION REPORT ................................................................................................................. 51
10.1.4 PASSCODES .................................................................................................................................. 52
10.1.4.1 FORGOTTEN PASSCODES ........................................................................................................... 52
10.2 STORE AND RECALL PMB SETTING FROM USB MEMORY .................................................................. 53
11.0 SERIAL INTERFACE .......................................................................................................... 56
11.1 RS-232 HARDWARE ................................................................................................................................... 56
11.2 USB SERIAL HARDWARE .......................................................................................................................... 56
11.3 INPUT COMMANDS .................................................................................................................................... 57
11.4 PRINTING RESULTS ................................................................................................................................... 57
11.5 ANALYZER CONFIGURATION THROUGH THE SERIAL INTERFACE ..................................................... 60
11.5.1 TEST PARAMETERS ...................................................................................................................... 60
11.5.2 PMB SETUP PARAMETERS .......................................................................................................... 61
11.5.3 ANALYZER RECALL PARAMETERS ............................................................................................. 62
11.5.4 REQUEST VALUES OF PARAMETERS ........................................................................................ 62
11.6 CONTINUOUS OUTPUT ............................................................................................................................. 63
12.0
SPECIFICATIONS & FEATURES ....................................................................................... 64
13.0 MENU STRUCTURE ............................................................................................................ 67
14.0 SAMPLE PREPARATION ................................................................................................... 73
15.0 GUIDANCE NOTES ............................................................................................................. 75
16.0 WARRANTY STATEMENT ................................................................................................ 79
1
| P a g e © Adam Equipment Company 2017