Tuthill Fill-Rite FR300V Serie Manual De Instalación Y Operación página 12

IMPORTANT! DO NOT open or attempt to repair the motor on your FR300V series pump. Opening the motor case can compromise the integrity of the Explosion
Proof construction and will void any existing warranty and certification (UL listing). Please refer to the warranty policy located on page 2.
ATTENTION!
The following information is for suffix "E" pumps and meters. Refer to the informa-
tion label applied to your pump to see if it is applicable.
Motor Plate Information
ENTRY THREADS ARE M20-1.5 6H
VOLT: 115/230 Hz: 60/50 HP: ¾
DUTY RATING: 30 MIN. FLA: 9.8/4.9/11.4/5.7
Serial Number and Year of Manufacture.
Tuthill
8825 Aviation Drive
Fort Wayne, IN 46809 USA
WARNING – DO NOT OPEN WHEN AN EXPLOSIVE ATMOSPHERE IS PRESENT.
Materials of Construction
Materials of construction of the external surface of the unit are: painted steel;
painted cast iron; painted aluminum; zinc plated steel.
Materials of construction of the wetted parts are: cast iron; steel; zinc plated steel;
300 series stainless steel; carbon; polyester; fluorocarbon; Teflon; brass; iron; copper;
buna; 400 series stainless steel; aluminum.
Repair and Maintenance
Contact the place of purchase for warranty repair and maintenance
Installation
Pump must be installed in compliance with EN 60079-14 or IEC 60079-14, as applicable.
Certificates for Compliance of Safety have been obtained for the following agencies for
products sold outside the US and Canada. Please refer to the tag on your particular
product for its particular compliance data.
Specific Conditions of Use
1. Consult the manufacturer if dimensional information on the flameproof joints
is necessary.
300H0745 Rev. 7
AMB TEMP: 40°C PH: 1 RPM: 1725/1425
INS: B
II 2 G
Ex db h IIA T4 Gb
FM09ATEX0075X
Ex db IIA T4 Gb
2809
IECEx FMG19.0014X
Fort Wayne, Indiana 46809 USA
tuthill.com | fillrite.com | sotera.com
Specific Conditions of Use (continued)
2. ISO Class 8.8, M6 hex-head screws (Yield Stress 640 MPa) shall be used to replace
the terminal cover fasteners.
3. ISO Class 8.8, M8 hex-head screws (Yield Stress 640 MPa) shall be used to replace
the stator housing fasteners.
4. An electrically conductive hose and nozzle must be used with flammable liquids.
To minimize static electricity buildup, always keep the nozzle in contact with the
container being filled during the fueling process.
The following standards were used to show compliance in the European Union:
EN IEC 60079-0:2018, Ed 7 "Explosive atmospheres – Part 0: Equipment –
General requirements"
EN 60079-1:2014, Ed 7 "Explosive atmospheres – Part 1: Equipment protection by
flameproof enclosures "d""
EN ISO 80079-36:2016, Ed 1 "Explosive atmospheres – Part 36: Non-electrical equip-
ment for explosive atmospheres – Basic method and requirements"
EN ISO 80079-37:2016, Ed 1 "Explosive atmospheres – Part 37: Non-electrical equip-
ment for explosive atmospheres – Non electrical type of protection constructional safety
"c", control of ignition source "b", liquid immersion "k""
Directive 2014/34/EU – Equipment and protective systems intended for use in potential-
ly explosive atmospheres.
Directive 2011/65/EU – Restrictions of the use of certain hazardous substances in
electrical and electronic equipment.
The following standards were used to show compliance for IECEx certification:
IEC 60079-0:2017, Ed 7
IEC 60079-1:2014, Ed 7
2809
Tuthill Corporation
8825 Aviation Drive
P (800) 634-2695
(+01) 260-747-7524
F (800) 866-4681
Tuthill UK LTD.
Birkdale Close Manners Industrial Estate
Ilkeston, Derbyshire
DE7 8YA UK
P +44 0 115 932 5226
F +44 0 115 932 4816