Installation (Fig.1); Switching On/Off - Shad BC22 Manual De Usuario

INSTRUCTION MANUAL
SHAD BC22
Welcome
Congratulations and thank you for purchasing a SHAD
BC22 device. This Bluetooth® device has been
especially designed to keep you connected to your
phone and listen to your favourite music while
travelling on your scooter or motorcycle.
The SHAD BC22 system is compatible with all
Bluetooth® devices that transmit audio (mobile
phones, smartphones, GPS navigators and other
devices) using the profiles specified in the manual.
This device is designed so that it may be wholly
integrated into your helmet. It can be operated and
paired easily through a single control button (1b).
A single red/blue LED indicator (1a) serves to display
connection status, pairing, battery charging and low
battery. The SHAD BC22 device weighs only 55 g.
For better use of the SHAD BC22 device, please read
this manual and keep it in a safe place or find it at
www.shad.es
Charging the SHAD BC22
Before using your SHAD BC22 device for the first time,
you must charge the device completely.
Connect the terminal (3) to the provided USB cable (5)
and then connect the cable to a USB charging port.
While charging, the red LED light will switch on (1a)
and it will switch off once charging has been
completed.
NOTE: Don't pull on the cable to disconnect it from the
USB port.
NOTE: As time goes by, batteries gradually lose their
fully charge. This is why it's important to charge the
battery fully before using the device and allow the
battery to use almost all of its charge in between
charging cycles.
WARNING: If you plan to store your SHAD device for a
long period of time, be sure to recharge it at least once
every six months to ensure perfect battery function.
8

Installation (fig.1)

The SHAD BC22 is very easy to install into a helmet.
Remove the side padding from the inside of the helmet
(if it can be removed) and place the devices (2) and
(4) at the height of your ears. The device is designed
so that the main unit with the boom microphone is
placed on the left side. The wire between devices (2)
and (4) must be stored inside the helmet, under the
padding. In order to affix the headphones, two Velcro
pads are provided (male and female) with an adhesive
backing (6,7). In case you need to use the Velcro, stick
the male part (6) of the pad onto the device and the
female part (7) onto the inside of the helmet.
Depending on the internal configuration of each type
of helmet, it may be necessary to use the entire Velcro
pad or only a part of it. In some cases, it may only be
necessary to stick the male part onto the device as the
inside of the helmet may have padding that can serve
as Velcro (female).
If needed, comfort pads (8) to place on the headpho-
nes are also provided, in order to improve comfort
against your skin.
The charging cable (3) must be placed on the
lateral-back section of the helmet so as to facilitate
access to charge the device.
Place the microphone (1) on the front section of the
helmet (close to and oriented towards your mouth).
Linking/Pairing
To use the SHAD BC22, it's necessary to pair it to the
Bluetooth® device you wish to connect it to (mobile
phone, GPS navigator). While the device is switched
off, hold the control button (1b) until the LED indicator
(1a) begins flashing in Red and Blue. The mobile
phone or GPS navigator will find the device under the
name SHAD BC22. Select the SHAD BC22 device
and, if necessary, enter the access code: 0000.
NOTE: Pairing is a process that only needs to be
completed once. When the SHAD BC22 is paired to a
specific device, both devices will connect automatica-
lly when switched off and on.

Switching on/off

Switching on: press and hold the button (1b) for a few
seconds until the speaker provides an acoustic signal
and the LED indicator (1a) begins to flash in Blue.