Tabla de contenido
Idiomas disponibles
Idiomas disponibles
Do not force tool. The correct tools will do the job
better and safer at the rate for which it is designed.
Disconnect the plug from the power source
before making any adjustment, changing
accessories, or storing the tool. Such preventive
safety measures reduce the risk of starting the tool
accidentally.
Store idle tools indoors. When not in use, tools
should be stored indoors in dry, and high or
locked-up lace, out of reach of children.
Maintain tools with care. Keep cutting tools sharp
and clean for best performance and to reduce the risk
of injury. Follow instructions for lubricating and
changing accessories. Inspect tool cord periodically,
and if damaged, have it repaired by an authorized
service facility. Keep handling surface dry, clean, and
free from oil and grease.
Check damaged parts. Before further use of the
tool, a guard or other part that is damaged should be
carefully checked to determine that it will operate
properly and perform its intended function. check for
alignment of moving parts, binding of moving parts,
breakage of parts, mounting, and any other condi-
tion that may affect its operation. A guard or other
part that is damaged should be properly repaired or
replaced by an authorized service center unless indi-
cated elsewhere in this manual.
SPECIFICATIONS
Motor Input . . . . . . . . . .120V~,60Hz, 14Amp
Hopper Size . . . . . . . . . . .394x270x200mm
. . . . . . . . . .(15-1/2"x10-5/8"x7-7/8")
No Load Speed . . . . . . . .2800R.P.M.
Net Weight . . . . . . . . . . .35Kg
PRECAUTIONS FOR USING TRISECTA
WARNING: Extreme caution should be
taken to ensure shreddable material does
not contain metal. Rocks, bottles. Cans or
other foreign objects.
CAUTION! Do not allow hands or any
other part of the body, or clothing to enter
inside the feeding chambers or discharge
chute, while machine is operating.
•
Wear gloves while operating the machine.
•
Before starting the machine, ensure that all
screws and other fasteners are properly secured.
•
Machine should be operated on firm level
surfaces only.
•
Before starting the machine, check that the
cutting chamber is empty.
•
Motor should be kept clean of debris and other
accumulations.
•
Keep all guards and deflections in good working
condition.
•
Stand clear of discharge chute at all times.
•
Do not over reach and keep face and body back
form the feed opening.
WEAR YOUR
SAFETY GLASSES
AND DUST MASK
•
Never pull the machine by the power cord and
keep cord away form water or sharp edges.
•
Disconnect the power cord when the machine is
not in use.
WARNING! If machine should become
clogged, switch off the motor, disconnect
the power cord, make sure all moving
parts are completely stopped before
cleaning clogged debris.
WARNING! Ensure the power cord is
always in good condition. A cord with
broken insulation is extremely dangerous
and can result in fire, electric shock or
serious personal injury.
WARNING! The operation of any tools can
result in foreign objects being thrown into
your eyes, which can result in severe eye
damage Before operating power tool,
always wear safety goggles or safety glasses
with side shields and a full face shield when
needed. We recommend wide Vision Safety
Mask for use over eyeglasses or standard
safety glasses with side shields.
HOW TO ASSEMBLE YOUR TRISECTA
1.
Push the large diameter section of the axle into
the axle tube and secure the axle into position
using the M8 x 40 hex screws and star washer.
(2 per side)
2.
Push the wheel and then the 12mm flat washer
over the axle.
3.
Push the split pin through the hole in the end of
the axle and bend the ends over using pliers.
4.
Fix on wheel covers.
HOPPER (FIG.2) Place the hopper on top of the feed
tube and align the fixing holes. Secure with the
safety set screws.
MAINTENANCE
Your Trisecta has been designed for a low level of
maintenance, involving routine cleaning and
inspection. The motor of the Trisecta is maintenance
free and requires no attention. For the best results
the blades must be kept sharp at all times. The blades
have dramatically less cutting power when blunt.
The Trisecta will tear rather than cut when the blades
are blunt. When this occurs rotate the double sided
blades or replace the blades immediately.
2
Fig. 1
Fig. 2
Tabla de contenido
