Cleaning And Maintenance; Disposal And Recycling - Robust RB-SD 3,6 Li Manual De Instrucciones Original

Anleitung_RB_SD_3_6_Li_SPK7__ 16.07.12 11:28 Seite 18
GB
6.2 Changeover switch (Fig. 2/Item 10)
The slide switch above the ON/OFF switch is for
setting the direction of rotation of the cordless
screwdriver and for preventing the cordless
screwdriver from being switched on inadvertently.
You can select between clockwise and counter-
clockwise rotation. Change the direction of rotation
only when the equipment is at a standstill. If you fail
to observe this point, the gearing may become
damaged. When the slide switch is in the middle
position, the ON/OFF switch is blocked.
6.3 ON/OFF switch (Fig. 2 / Item 9)
Press the On/Off switch to switch the cordless
screwdriver on. Release the ON/OFF switch to
switch off the tool.
6.4 LED lamp (Fig. 1/Item 2)
The LED lamp (2) can be used in poor lighting
conditions to illuminate the area where you want to
screw. To switch ON, press the switch (4) and to
switch OFF press the switch (4) again.
6.5 Angle setting (Fig. 1,3/Item 3)
The screwdriver can be locked into 2 different angle
settings. To do so, press the locking button (3) and
move the screwdriver into the desired position. Then
release the locking button (3).
Important. Before you switch on the screwdriver,
make sure that it is correctly locked in the angle
position in question.
6.6 Battery capacity indicator (Fig. 4/Item 5)
Press the button for the battery capacity indicator (6).
The battery capacity indicator (5) indicates the
charge state of the battery on 3 colored LEDs.
All LEDs illuminate:
The battery is fully charged.
The yellow and red LED illuminate:
The battery has an adequate remaining charge.
Red LED:
The battery is empty, recharge the battery.
6.7 Changing the tool (Fig. 5)
Important! Set the changeover switch to its centre
position whenever you carry out any work (for
example changing the tool, maintenance work, etc.)
on the cordless screwdriver.
Pull back and hold the locking sleeve (13).
n
Insert the bit (a) into the bit chuck (1) and let go of
n
the locking sleeve (13).
Check that it is secure by attempting to pull the
n
tool apart again.
18
6.8 Screwdriving
We recommend using self-centering screws (e.g.
Torx screws, recessed head screws) designed for
reliable working. Be sure to use a bit that matches
the screw in shape and size. Set the torque, as
described elsewhere in these operating instructions,
to suit the size of screw.

7. Cleaning and maintenance

Always pull out the mains power plug before starting
any cleaning work.
7.1 Cleaning
Keep all safety devices, air vents and the motor
n
housing free of dirt and dust as far as possible.
Wipe the equipment with a clean cloth or blow it
with compressed air at low pressure.
We recommend that you clean the device
n
immediately each time you have finished using it.
Clean the equipment regularly with a moist cloth
n
and some soft soap. Do not use cleaning agents
or solvents; these could attack the plastic parts
of the equipment. Ensure that no water can seep
into the device.
7.2 Maintenance
There are no parts inside the equipment which
require additional maintenance.

8. Disposal and recycling

The unit is supplied in packaging to prevent its being
damaged in transit. This packaging is raw material
and can therefore be reused or can be returned to
the raw material system.
The unit and its accessories are made of various
types of material, such as metal and plastic.
Defective components must be disposed of as
special waste. Ask your dealer or your local council.
9. Storage
Store the equipment and accessories out of children's
reach in a dark and dry place at above freezing
temperature. The ideal storage temperature is
between 5 and 30 °C. Store the electric tool in its
original packaging.