Electrical Characteristics; Usage Instructions - CANGAROO GLOW Instrucciones De Uso

•Do not use spare parts which are not the original ones supplied by the manufacturer or importer.
•This product is a personal care item and should not be shared between mothers.
•Do not attempt to remove the pump body from your breast while under vacuum. Turn the unit off and break the seal
between your breast and the silicone pad with your finger, then remove the pump from your breast.
•Never use while pregnant as pumping can induce labor.
•Do not leave and do not store the product in a place with very high room temperature or under direct sunlight.
•The product should not be left unattended when plugged into the electrical wall socket.
•Before starting the breast pump, first connect the adapter to the electric breast pump, then securely connect the
adaptor to the electric socket.
•Wash, rinse and sterilize the appropriate pump parts before each use.
•Never wash and sterilize the electrical parts of the product – the motor of the pump and the AC adaptor in order not to
cause permanent damage to the product.
II. PARTS
See the separate pictures for the parts of the breast pump on page 1!
A: Massage function; B: Suction function; C: Battery; D: Levels; E: ON/OFF; F: Regime; G: Decrease; H: Increase; I: Safety
fuse; J: Silicone pad; K. Pumping mechanism; L: USB Cable; M: Silicone gasket; N: Pump body; O: Valve; P: Bottle; Q: Bottle
stand
III. ELECTRICAL CHARACTERISTICS
• Battery voltage: 5 VDC
• Battery capacity: 1300 mAh
• BATTERY CHARGER STANDARDS: Input: AC115V – 230V; Output: 5VDC, 1.0 A
• Charging time: 100 minutes
•Method of control: buttons
• Display: LCD
IV. CHARGING THE ELECTRIC MOTOR OF THE PUMP
The breast pump has built-in rechargeable battery. Please, for recharging, use USB cable, provided with the pump.
When the battery is recharging, the symbol ( ) flashes and when the battery is recharged – it lights permanently.
When the battery is almost exhausted, the symbol begins to flash. Please, stop using and recharge it.
The breast pump must not be used, while it is recharging.
You can use USB cable for recharging with every source of DC5V current.
V. ASSEMBLY OF THE ELECTRIC BREAST PUMP
See the assembly figures at page 3!
1. Insert the valve on the bottom of the pump's body and tighten it well to prevent leakage of air.
2. After step 1, turn the pump to the bottle clockwise.
3. Insert the piston from the top, making sure that it fits well from all sides.
4.Put the head of the pump from the upper part of the body and ensure that it fit tightly and turn clockwise.
5.Put the silicone pad, as shown on the picture and ensure that it is tightly fitted.
6.Put the breast pump on the basis.
VI. USAGE INSTRUCTIONS
WARNING! NEVER STERILIZE AND NEVER DIP INTO WATER THE PUMPING MECHANISM AND THE AIR TUBE THAT
CONNECTS THE PUMP BODY AND THE MECHANISM. OTHERWISE, THE BREAST PUMP WILL NOT BE ABLE TO WORK.
1.Wash your hands thoroughly and make sure your breasts are clean. Squeeze a little breast milk from each breast to
ensure there's no blockage. Make sure your breast pump is sterilized and properly installed.
2.Relax in a comfortable chair, leaning slightly forward (use cushions to support your back).
3. Place the pump pad, so it sticks tightly to your breast and make sure the nipple is in the middle.
4. Press to turn the breast pump on. After that the screen turns on and symbol for massage and symbol for
battery will appear.
5. Press the "+" button to increase the level and the "-" button to decrease the level. There are 10 levels of massage
function.
6. After the breast milk starts to run, press to turn on the suction function. When the symbol changes to , reduce
the speed.
12