Important Safety Instructions - DSC WTK5504 Manual Del Usuario Y Operador

Read and save these instructions! Follow all warnings and instructions specified within this document and/or on the
equipment. Always ensure you obtain the latest version of the User Guide. Updated versions of this User Guide are
available by contacting your distributor.
Use these instructions in conjunction with the Installation Manual of the alarm panel with which this equipment is
intended to be used.

IMPORTANT SAFETY INSTRUCTIONS

To reduce the risk of fire, electric shock and/or injury, observe the following:
• Do not spill any type of liquid on the equipment.
• Do not attempt to service this product yourself. Opening or removing the cover may expose you to dangerous volt-
age or other risk. Refer servicing to qualified service personnel. Never open the device yourself.
• Do not touch the equipment and its connected cables during an electrical storm; there may be a risk of electric shock.
• Do not use the Alarm System to report a gas leak if the system is near a leak.
REGULAR MAINTENANCE AND TROUBLESHOOTING
Keep your WTK5504 Touchscreen keypad in optimal condition by following all the instructions that are included
within this manual and/or marked on the product.
HANDLING PRECAUTIONS
• Do not subject the touchscreen to mechanical shock (e.g., dropping or striking). Mechanical shock could damage the
glass display.
• If the touchscreen glass is damaged, the liquid crystal fluid inside could leak out. Avoid contact with the liquid crys-
tal fluid. If the liquid crystal fluid comes into contact with your skin or clothes, promptly wash it off using soap and
water.
• Do not apply excessive force to the display surface or adjoining areas. Excessive force will distort the image on the
display.
• Do not use hard or sharp implements to operate the touchscreen. Operating the touchscreen with any implement
harder than a finger could scratch the display.
• Do not attempt to disassemble the LCD Module.
CLEANING
• The WTK5504 features a cleaning mode that disables the Touchscreen for thirty seconds and prevents unintended
button presses during cleaning. To enter cleaning mode press More > Functions > Clean Mode.
• If the display surface is contaminated, breathe on the surface and gently wipe it with a soft, dry cloth. If still not com-
pletely clean, moisten cloth with isopropyl alcohol.
• Clean the touchscreen with a soft cloth and isopropyl alcohol. Use of other cleaners such as water, ketone (e.g., ace-
tone), and/or aromatic solvents (e.g., benzene and toluene) may damage the display. Do not use abrasives, water,
thinners, solvents or aerosol cleaners (spray polish), any aromatic solvents, ketones etc. that may enter through holes
in the WTK5504 Touchscreen keypad and cause damage.
TROUBLESHOOTING
Occasionally, you may have a problem with your system. If this happens, your Alarm Controller will identify the
problem and display an error message. Refer to the provided list when you see an error message on the display. If
additional help is required, contact your distributor for service.
WARNING: This equipment, the WTK5504 Touchscreen keypad, shall be installed and used within an environ-
ment that provides the pollution degree max 2 and over-voltages category II non-hazardous locations, indoor only. It
is designed to be installed, serviced and/or repaired by service persons only [service person is defined as a person
having the appropriate technical training and experience necessary to be aware of hazards to which that person may
be exposed in performing a task and of measures to minimize the risks to that person or other persons]. There are no
parts replaceable by the end-user within this equipment.
These safety instructions should not prevent you from contacting the distributor and/or the installer to obtain any
further clarification and/or answers to your concerns.
CAUTION: Use ONLY the supplied power supply with this equipment. Use of any other type of power supply may
create a risk of fire and/or electric shocks. This device has no on/off switch to disconnect or connect to the mains. The
plug of the direct plug-in power supply serves as means of disconnection. The socket outlet in which the power supply
is connected to the mains shall be installed near the equipment and shall be accessible. Ensure that the cable that comes
from the power supply does not create a tripping hazard between the socket outlet and the equipment.
About Your Security System
Your DSC Security System has been designed to provide you with the greatest possible flexibility and convenience.
Read this manual carefully and have your installer instruct you on your system's operation and on which features
have been implemented in your system. All users of this system should be equally instructed in its use. Fill out the
"System Information" page with all of your zone information and access codes and store this manual in a safe place
for future reference.
NOTE: The PowerSeries, Alexor, and Impassa security systems include specific false alarm reduction features and
are classified in accordance with ANSI/SIA CP-01 Control Panel Standard - Features for False Alarm Reduction.
Please consult your installer for further information regarding the false alarm reduction features built into your sys-
tem as all are not covered in this manual.
Carbon Monoxide Detection (must be enabled by your Installer)
This equipment is capable of monitoring carbon monoxide detectors and providing a warning if carbon monoxide is
detected. Please read the instructions that are available with the carbon monoxide detector.
1