Tabla de contenido
Idiomas disponibles
Idiomas disponibles
Playback
The USB player supports WAV, WMA and MP3 playback through
USB.
1. Power on the device.
2. Insert an appropriately formatted (FAT32) USB flash drive.
3. On the main menu, select "Playback" and press the PLAY
button.
4. Press the PLAY button to play the current track, or the << and
>> buttons to skip forward and backwards between tracks.
5. Press the MENU button while in the Playback mode to access
the File Browser, Delete File, Repeat Mode and Volume Control
functions.
6. Press and hold the MENU button for three seconds to exit
playback mode and return to the main menu.
Folders - Freely navigate songs in each folder on USB flash disc
using the << and >> buttons. Press PLAY button to select, press
MENU button to go back.
Repeat Mode - There 4 repeat modes available.
No Repeat - Play each file in the current folder or root for once.
Repeat one - Constantly repeat selected song.
Repeat Folder - Constantly repeat all the song in the certain
folder or root.
Random – Enables random playback of files in current folder
or root.
Record
Users can record high quality WAV format
1. Power on the device.
2. Insert an appropriately formatted (FAT32) USB flash drive.
3. In the main menu, select "Record" and press the PLAY button
to enter recording mode.
4. Select between the 128 kbit/s and 192 kbit/s WAV recording
modes and press the PLAY button.
5. Record mode will begin in standby/pause. Push the Play/Pause
button to begin recording. The unit will save the recorded file
into the RECORD directory on the USB device.
6. Push the Play/Pause button to pause recording. Pushing the
Play/Pause button again will resume recording from the position
at which it was paused.
7. Press the MENU button at any time to save the recording. Once
the recording is saved, the system will automatically skip to the
next track.
8. To exit out of the playback mode and return to the main menu,
press and hold MENU button for three seconds.
NOTE: The USB rotary control will adjust the playback level only
and will not affect recording levels. The only level controls that
will affect the recording level are those found on the individual
input channels.
Safari 1000M / Safari 1000 Lite
Wireless Microphones (Safari 1000M)
Lock Button
Auto Scan Button
RF Status
Infrared
One-Touch Auto Scan
1. Power-on the Safari One-Touch Autoscan wireless receiver
(WR-1) by turning the volume knob clockwise. You should hear
a click sound from the knob.
2. Power-on your handheld microphone (WM-1) or beltpack unit
(WB-1)
3. Hold the WM-1 / WB-1 close against the receiver WR-1 and
push the Scan button on the WR-1 for 4 to 5 seconds until
the numeric channel LED digits start to automatically change,
indicating that the autoscan is finding the best wireless channel.
4. The autoscan process is finished when the LED display stops
at the optimal channel. At this point, the RF LEDs will activate.
If the RF LEDs on the WR-1 do not light on, the connection has
not been established successfully. To reinforce the connection,
click the Lock button while holding the WM-1 or WB-1 close to
the receiver.
5. Upon a successful connection, the AF LEDs on the WR-1 will
activate as you speak into the microphone.
Manual Scan
1. Power-on the Safari One-touch Autoscan wireless receiver
(WR-1) and the microphone transmitter (WM-1 or WB-1).
2. Push the Scan button on the WR-1 for 2 seconds. The numeric
LEDs on the WR-1 will begin to blink. To manually select fre-
quency, continue to click the Scan button until you reach the
desired channel.
3. Hold the WM-1 / WB-1 close against the receiver and push
the Lock button to confirm the channel and establish the link
between the microphone transmitter and receiver. At this point,
the RF LEDs will activate and the AF LEDs will respond to the
microphone signal. If the connection is not established, reat-
tempt the manual or autoscan process.
Channel LED
Power Switch
Volume Knob
Volume Gain
3
Capítulos
Tabla de contenido
