Tabla de contenido
Idiomas disponibles
Idiomas disponibles
2. Preparing for use
2.1 Electrical connection
Before connecting the machine to the power supply,
check that your supply voltage corresponds with that
marked on the rating label on the machine.
UK only
The supply cord for 230v models is fitted with a plug
containing a 13 amp fuse. Should the fuse require
replacement it must only be replaced by a 13 amp
fuse conforming to BS1362, and the fuse cover must
be refitted. If the fuse cover is lost the plug must not
be used until the correct replacement cover is fitted.
Should an extension cord be used, ensure cord rating
is adequate for the equipment. Do not use extension
cord in coiled condition as this could result in
overheating of the cord. The power supply cord plus
any extension leads should not exceed 30 m in total.
The cross-section of any extension cable wiring must
be at least 2, 5 mm².
THIS
WARNING
–
EARTHED.
2.2 Fitting pads
WARNING - This appliance has been designed for use
with quality burnishing pads only. The fitting of
inappropriate pads may affect its performance and safety.
WARNING - Ensure the machine is switched off before
adding or changing accessories.
• Fit pads suitable for the speed of the machine and the
surface to be polished, as recommended by the pad
manufacturer.
• Always ensure machine is switched OFF by the key
operated switch (10) and the key removed before fitting
or removing pads.
CAUTION – If spray bottle is fitted, lower handle (5) gently
to avoid damaging bottle.
• Remove key. Fold handle and carefully tilt machine on
rear castor.
• Remove pad retainer noting anti-clockwise thread.
• Press cleaning pad centrally onto drive board. Secure
pad using pad retainer.
• Return machine to upright position.
IMPORTANT - Never allow the cleaning head to rest on
the brush or drive disc and pad when not in use.
3. Controls
The operating controls are located on the handle (5).
Please refer to page 1.
APPLIANCE
MUST
4. Operation
4.1 Starting the machine
WARNING - Never start the machine without a pad fitted.
• Do not keep the machine rotating on one spot, as this
could cause overheating and damage the floor surface.
• Turn the key operated switch (10) to the ON position.
• With the handle (5) set at a comfortable working height
and with both left and right hands on the handle,
depress both interlock buttons (1) with the thumbs and
squeeze both switch triggers (2) to start the machine
• Once the machine has started the interlock buttons (1)
can be released. The machine will operate with either or
both of the switch triggers (2) held.
• To stop the machine release the switch triggers (2).
• Normal movement of the machine is in a forward and
backward direction.
4.2 Orbis spray system
• Pump plunger on top of bottle 10-15 times to build up
spray pressure.
• Pull accessory trigger on handle to spray solution onto
BE
the floor.
4.3 When cleaning is finished
• Switch OFF machine, raise cleaning head and remove
pad.
• Check battery life indicator and recharge as necessary.
4.4 Charging the batteries
WARNING - Only recharge the battery when the battery
life indicator (12) is in the red zone (two lights remaining).
Opportunity / top up charging will damage the batteries.
This will cause run time to fall and overall battery life will
be affected. AVOID TOP UP CHARGING. Charge only in
a well-ventilated area.
• Note when 1 RED LED is showing on the battery life
indicator the internal controller will disable the machine.
• Take the battery charging lead supplied with the
machine plug into the mains supply, ensuring that the
supply matches the rating plate.
• To fully charge the batteries takes approximately 8
hours.
The Battery charge indicator lights (12) show:-
Initially when charging:
• Red LED will be lit during the first phase of charging
• The yellow LED will be lit when the initial bulk charge is
taking place.
• When the green LED light is flashing the battery is about
80% charged.
• The GREEN LED shows when the charger has switched
over to float charge and that the battery is ready for use.
• The charger is set for GEL batteries only.
• Do not operate the machine when connected to the
mains electrical supply.
5
Tabla de contenido
