Kobra 410 TS Instrucciones De Manejo página 10

FEATURES
The KOBRA 410TS models are shredders suitable for single
computer printouts,CD-ROMS,DVDS,FLOPPY DISKS and
CREDIT CARDS.
For technical specifications and shredding capacity see table
on page. 25
INSTALLATION
For machines with a detachable power plug, use an easily
accessible socket in the vicinity of the machine.
Once the machine has been unpackaged, open the door (A), take out the stand (B) as indicated in figure 1, and take
out the bag holder (C); fit the plastic bag (D) which comes
with the machine, to the bag holder (C) and reposition it
on frame (B); press the frame (B) fully into place and close
the door (A).
The KOBRA 410TS shredders come with a canvas bag (H) for
separate collection of CDs/DVDs/FLOPPY DISKs and CREDIT
CARDS.
TOUCH SCREEN TECHNOLOgy.
KOBRA 410TS shredders come with TOUCH SCREEN
technology.
Shredder functions are activated by simply brushing the
desired function on the control panel.
- FORWARD: brush the FORWARD button and the
shredder puts the cutting blades into forward gear
and carries out a shredding cycle which lasts about
7 seconds making it possible to shred transparent
material which might not activate the electronic eyes /
photo cells.
- STOP: brush the STOP button and the machine stops
instantly.
- REVERSE: brush the REVERSE button and the shredder
puts the cutting blades into reverse.
- OIL : signals that the shredder is out of oil.
USINg THE SHREDDER FIg.4
Once the shredder has been plugged in, press the ON/OFF
(P and E), the led (F) on the control panel lights up and the
machine is ready for operation.
If the shredder is then not used for 8 seconds the led bar
(F) switches off and the machine goes on stand-by and zero
consumption and the ENERGY SMART (G) led comes on.
When material to be shredded is inserted the machine
switches on again automatically. If the shredder is not used
for four hours, the machine automatically cuts off the power
supply and switches off the ENERGY SMART led (G).
To switch the shredder back on, press the ON/OFF switch (E).
SHREDDINg SINgLE SHEETS FIg.4
When sheets are inserted into the paper throat (1) the led
light bar (F) comes on (if off) and the machine automatically
starts shredding as two electronic eyes (1A) located inside
the throat detect the movement of the sheets of paper.Then,
once the sheets have been shredded, the cutting blades stop
automatically after a few seconds.
The shredder is fitted with a LOAD METER (2), which allows
for constant monitoring of the shredding capacity of your
machine.
Insert the sheets to be shredded in the paper throat (1) and
the led (2) comes on.
The lighting sequence of the led (2) depends on the quantity
of paper inserted into the shredder.
For continuous and efficient shredding, try to ensure that
only the first four blue leds on the load meter (2) are on.
If the quantity of paper increases, the rest of the leds light
up; first the yellow, and then the red lights.
If the quantity of paper inserted exceeds the shredding
capacity of the machine, the shredder cuts out and the paper
jam light (3) comes on.
The shredder then goes into automatic reverse for a few
seconds to free the cutting blades and then stops.
Remove the excess paper from the throat (1) to free the
electronic eyes, then insert a smaller quantity of paper into
the throad and the machine will automatically begin a new
shredding cycle.
It is recommended that paper jams caused by inserting
excessive quanitities of paper be kept to a minimum and
the machine be operated at less than maximum capacity in
order to prolong the life of the mecahnical parts and the
shredder.
AUTOMATIC OILER SySTEM
KOBRA 410TS shredders feature a special automatic system
for lubricating the cutting knives.
INSTALLATION fIg.1,2,3
After unpacking the shredder, open the door.
Unscrew the sealed cap on the oil container (I) and discard,
insert the oil tube (L) and tighten the lid (M) as shown in
figure 2.
Pull out the holder (B) as shown in figure 1, take the plastic
bag (N) fig.3 which comes with the shredder and fit it to
the bag holder (o) and put it inside the canvas bag (H) as
shown in figure 3.
OPERATION;
Plug in the shredder to the power supply and press the ON/
OFF (E) switch fig.4, and the led bar (F) fig.4 comes on and
the shredder is ready to go.
During the first few minutes of operation, the led (8) fig.4
may flash since the oil tube is not yet completely full. In
order to speed it up and turn off the OIL led (8), operate
the shredder on empty for ¾ minutes by pressing the
FORWARD button (9) fig.4.
Now your shredder is ready and the cutting blades are oiled..
Lack of oil in the container is signalled by the OIL led (8)
fig.4 flashing .
10