Preparing To Use Your Grill - Weber GO-ANYWHERE Manual Del Proprietário

WHAT IS A LEAK CHECK?
The fuel system in your grill features
connections and fittings. A leak
check is a reliable way to make sure
that no gas is escaping from any of
the connections or fittings.
Although all factory-made
connections have been thoroughly
checked for gas leaks, it's important
to perform a leak check before
using your grill for the first time, as
well as anytime you disconnect and
reconnect a fitting and each time you
perform routine maintenance.
m DANGER
Do not use an open flame to check for gas
leaks. Be sure there are no sparks or open
flames in the area while you check for
leaks. Sparks or open flames will result
in a fire or explosion, which can cause
serious bodily injury or death and damage
to property.
m WARNING: The gas connections of your
gas grill have been factory tested.
We do, however, recommend that you
leak check all gas connections before
operating your gas grill.
m WARNING: Perform these leak checks
even if your grill was dealer or store
assembled.
m WARNING: You should check for gas
leaks every time you disconnect and
reconnect a gas fitting.
NOTE: All factory-made connections have been thoroughly
checked for gas leaks and the burners have been flame-
tested. As a safety precaution, however, you should check
all fittings for leaks before using your Weber® gas grill.
Shipping and handling may loosen or damage a gas fitting.

PREPARING TO USE YOUR GRILL

PARTIAL DISASSEMBLY OF YOUR GRILL FOR
A LEAK CHECK
In order to do the leak check, you need to have access
to the gas valve, which will require some simple grill
disassembly.
Confirm that Grill Is Off
A) Make sure regulator control knob is turned off by
pushing it in and turning it counterclockwise to the off
position.
B) Make sure burner control knob is turned off by
pushing it in and turning it clockwise to the off ( )
position.
Remove Burner Control Knob Cover
You will need: An 11/16" Wrench.
A) Remove burner control knob (1). Make sure gas valve
remains in the off position.
B) Using an 11/16" wrench or pliers, remove brass hex
nut from valve stem (2).
C) Pull burner control knob cover away from grill (3).
Your grill is now ready for a leak check.
CHECKING FOR GAS LEAKS
You will need: A spray bottle or brush or rag and a soap-
and-water solution. (You can make your own soap-and-
water solution by mixing 20% liquid soap with 80% water;
or, you can purchase solution in the plumbing section of
any hardware store.)
A) Verify burner control knob is turned to the off ( )
position.
B) Turn gas supply on by turning the regulator control
knob clockwise (4).
m WARNING: Do not ignite burner when
leak checking.
C) To check for leaks, wet fittings with the soap-and-
water solution, using a spray bottle, brush or rag. If
bubbles form, or if a bubble grows, there is a leak.
Apply the soap-and-water solution to the following
connections:
a) Regulator-to-cartridge connection (5).
m WARNING: If there is a leak at
connection (5), remove the cartridge.
DO NOT OPERATE THE GRILL. Install
a different cartridge and recheck for
leaks with soap-and-water solution.
If a leak persists after installing a
different cartridge, turn off the gas. DO
NOT OPERATE THE GRILL. Contact the
Customer Service Representative in your
area using the contact information on
our web site.
Log onto www.weber.com
b) Valve-to-regulator connection (6).
m WARNING: If there is a leak at
connection (6), turn off the gas. DO
NOT OPERATE THE GRILL. Contact the
Customer Service Representative in your
area using the contact information on
our web site.
Log onto www.weber.com
D) When leak checking is complete, turn gas supply off
at the source and rinse connections with water.
NOTE: Since some leak test solutions, including soap and
water, may be slightly corrosive, all connections should be
rinsed with water after checking for leaks.
Reinstall Burner Control Knob Cover
You will need: An 11/16" wrench.
A) Place burner control knob cover onto grill.
B) Using an 11/16" wrench or pliers, reinstall brass hex
nut onto valve stem.
C) Reinstall burner control knob. Make sure gas valve
remains in the off position.
m WARNING: Make sure that all parts
are assembled and hardware is fully
tightened before operating the grill.
Your actions, if you fail to follow this
product warning, may cause a fire, an
explosion, or structural failure resulting
in serious personal injury or death as
well as damage to property.
Now you are ready to use your grill.
REMOVING THE LPG CARTRIDGE
When your LPG cartridge needs to be replaced, follow
these instructions to remove it.
A) Make sure the burner control knob is turned off by
pushing it in and turning it clockwise to the off ( )
position.
B) Make sure the regulator control knob is turned off by
turning it counterclockwise.
C) Unscrew disposable cartridge from regulator by
turning cartridge counterclockwise.
3
.
®
6
.
®
1
2
5
4
5
WWW.WEBER.COM
®