Tabla de contenido
Idiomas disponibles
Idiomas disponibles
Insert in every hole a 1/4" plastic dowel (included),
then insert in each plastic dowel a 1/4" x 1" screw
(included) no more than 2 cm deep (S1).
Set the previously ensemble body with grids and
blades on the wall support attachment (S2) and tight
it from behind with the fixing knob (S3).
Finally set the display on the previously set wall
screws (S4) and make sure it is properly set (S5).
Swing pivot:
Fig. K
Push
8.
down firmly
The swing pivot may not
be assembled to the engine
Swing
body.
pivot
Find the swing pivot inside
hole
one of the plastic bags that
contain parts of the fan. Introduce the pivot inside
the engine body hole assigned for it and push down
firmly until a "click" sound is heard and make sure
the pivot is correctly assembled. (Fig. K)
Operation mode
Make sure to set the fan on a stable and firm
surface, avoid rugs or carpets where it can tangle.
Make sure the unit is properly plugged to the
electric power supply, not before you verify the
appliance is off.
In order to start the fan push the speed button
desired: 1=Low; 2=Medium; 3=High
In
order
to
refresh
recommendation is to use oscillating mode
by pulling the swing pivot upwards to start
oscillation and pushing down again to stop it.
The fan's head angle can be horizontally adjusted
by pulling the swing pivot upwards so that it will
move on 150 oscillation range so you can set it to
0
the desired position by pushing the pivot down in.
Make sure before starting the operation of the
fan than it is set more than 3.94 in away from any
strange object which may block the air flow, such
as a walls, curtains or furniture.
ATTENTION: Make sure to turn off the fan by
pushing the off button "0", before you decide
to move it to another place.
Pilot light / Night light
The pilot light helps you locate the fan on the darkness.
You turn it on by pushing the button "L" once, as you
turn it off by pushing the off button "0" once.
CLEANING AND MAINTENANCE
Remember to unplug the fan from the electric
power supply every time after finishing using it.
In order to clean the fan exterior make sure to use
a dry piece of cloth lightly wet with a soft liquid
soap. Never submerge the fan in water or any
other fluid, nor let any water leak into the inside
of the fan. Avoid using either corrosive or flamma-
ble substances such as gasoline, thinner, etc. since
this damage the fan and produce toxic vapors, as
well.
We recommend to follow these steps in order to
clean the blades:
4
CZST180BS-EU
CZST180WS-EU
www.comfortzoneproducts.com
large
rooms,
our
1. Remove the front grid.
2. Clean the blades with a dry piece of cloth lightly
wet with a soft liquid soap.
3. Make sure to put back the safety grill's fixing
locks and that these firmly holds both grills (front
and back). Make sure the fan is completely dry
before starting it again.
STORAGE
Make sure to turn the "stand fan" off. Make sure the
blades of the "stand fan" are completely stopped.
Make sure not to tangle around the appliances the
electric power cord, roll it in circles without forcing it.
Storage both appliances in a clean a dry space, and
keep it always in a vertical position.
This product employs overload protection (fuse). A
blown fuse indicates an overload or short-circuit
situation. If the fuse blows, unplug the product from
the outlet. Replace the fuse as per the user servicing
instructions (follow product marking for proper fuse
rating) and check the product. If the replacement
fuse blows, a short-circuit may be present and the
product should be discarded or returned to an
authorized service facility for examination and/or
repair.
Fuse Replacement:
1. Grasp plug and remove from the receptacle or
other outlet device. Do not unplug by pulling on
cord.
2. Open fuse cover by sliding open fuse access cover
on top of attachment plug towards blades. See Fig 2.
3. Remove fuse carefully. Use a small tool to pry the
end of the fuse from holder cavity. Be careful not to
break glass window.
4. Replace fuse. WARNING: Risk of fire. Replace fuse
only with identical 2.5 or 5.0 Amp, 125 Volt fuse
(3.6mm x 10mm).
5. Be sure fuse is properly seated within its cavity.
Close fuse cover by sliding it back to its original
closed position.
Fig 1
Fig 2
Slide Cover to Open
Fig 3
Tabla de contenido
