Nüby NTNV 67692 Manual De Instrucciones página 42

Sterilisation instructions :
1.When ready to begin, insert plug into wall outlet. You will hear a single beep.
2
2. Pour 45 ml of water directly 3a. Disassemble teat from screw
into the warming basin or into ring. Place teat into the lift-out
the measuring cup if you intend basket first.
to travel with the product.
*Note: The lid may not completely close when sterilising taller bottles, however, sterilisation will still occur inside bottle. Keep hands and face away from lid opening as steam will be very
HOT.
6a
7. When sterilisation is complete, the center dot will turn SOLID GREEN. The unit will beep for 5 seconds and then turn off automatically. .
8. Remove the lid carefully by the handle. LID WILL BE VERY HOT. Keep hands and face away from unit when opening lid.
8
STERILISATION instructions for Soothers and Small Accessories
The basket also allows soothers and small parts such as teats, lids and screw rings to be sterilised quickly and easily. The basket must be in the chamber with the lid on for the sterilising
process to work properly.
• Please note- only items that are able to withstand the heat of steam sterilisation (as instructed by individual item's washing instructions) can be used with this feature.
• Item must be small enough so that it is completely contained within the lift-out basket. Do not use with items that extend through the basket's open areas, into the warming basin. The
sterilising lid must be completely in place.
• Before placing item into basket, remove all foreign material from item with soapy water. Rinse thoroughly. This must be done before any disinfection
process so the foreign material will not prevent disinfection.
• Please note- preheating is not necessary or recommended.
1. When ready to begin, insert plug into wall outlet. You will hear a single beep.
2. Measure 45 ml of water and pour directly into the warmer basin.
To Clean :
Clean unit and parts before initial use and after each subsequent use.
Always unplug unit and ensure that it is cool before cleaning. Warming and Sterilising Unit: Wipe surface of unit as well as inside of the warming basin with a damp cloth or sponge using
mild liquid soap. Wipe with clear water. Do not submerge unit. Measuring Cup, Lift-out Basket, Adapter Ring, and Sterilising Lid: Dishwasher safe (top rack) or wash with soapy water. Rinse
with clear water. Allow to air dry. Do not use scouring pads, abrasives or solvents for cleaning; they may damage the appliance and its surfaces.
To De-scale:
It is helpful to de-scale your Bottle Warmer every four weeks to ensure that it continues to work properly. To de-scale, mix 2 oz.(59ml) of white vinegar with 4 oz. (100ml) of cold water and
pour into the Warming Basin. Allow liquid to stand in the unit until any deposits (limescale) have dissolved. Discard liquid and rinse with clear water. Any other servicing should be performed
by an authorized service representative.
42 - NTNV 67692
3a
3b. Lightly place the screw
ring in the lift-out basket over
the teat.
6a. Press the POWER button ( ) once to
turn your unit ON. All other icons will light
up and begin FLASHING GREEN.
3b
4
4. Place bottle base upside
down in the basket on top of the
screw ring and teat. Always use
this basket to prevent damage
to bottles, teat, etc.
6b
3. Place pacifier or small accessory in the lift-out basket. Always use this basket to prevent
damage to pacifiers and small accessories.
4. Place the sterilising lid on top of the unit.
5. Follow the sterilising bottle directions, numbers 5-7.
5
5. Place the lid* on top. Only use
the lid for sterilising.
6b. Press the Power ( ) button again to
choose the steam sterilising icon ( ). The
center dot will begin FLASHING GREEN
and the unit will begin the sterilising
process automatically. (Approximately
8 minutes)