Section 7: Troubleshooting; Section 8: Warranty - Blendtec DESIGNER Serie Manual Del Propietário

3� BLENDER JAR IS DISHWASHER SAFE—TOP RACK ONLY!
4� Extreme temperatures damage the lower seal of the jar� We recommend handwashing
to prolong the life of the blender jar� We do not recommend the jar be used or
exposed to, temperatures above boiling (212°F, 100°C)�

SECTION 7: TROUBLESHOOTING

While we don't expect you to have any problems with your blender, sometimes
failures do occur� Use the following guidelines to see if the problem is easily fixed
or requires service�
7.1 BLENDER MOTOR WILL NOT TURN ON (NO POWER)
If the blender motor will not turn on, try the following:
1� Determine if the Power Button is lit� Absence of a lit Power Button indicates a
lack of power to the unit�
2� Make sure the blender is plugged in�
3� Check your house circuit breaker switch or fuse to make sure it is set to the
ON position�
4� Press the Power Button located on the upper right hand side of the touch area�
5� Unplug the power cord from the wall receptacle, wait 5 seconds, then plug power
cord back in�
7.2 ERROR MESSAGES ON DISPLAY
If this icon appears on your blender, it indicates that the motor is overheating� The
blender has been disabled until the unit cools to operating temperatures� Turn off
and unplug the unit� Allow it to cool for at least 20 minutes, then plug it back into
check if the icon is still visible� If the icon does not disappear after 20 minutes or
more of cooling time, please call your Blendtec Service Agent�
If this icon appears on your blender it indicates that more than one touch sensor
on the blender has been touched� This icon should only appear as long as the
multiple sensor areas are being touched� If this icon remains on when no one is
touching the touch area unplug and re-plug in the blender� If the problem persists
please contact your Blendtec Service Agent�
If this icon appears on your blender, please turn off and unplug the unit� Check
the blender jar for blockage and clear if necessary� Plug in the unit and turn the
blender on again� If the icon is still visible on your blender, contact your Blendtec
Service Agent�
If this message appears on the LED information center it indicates there has been
an error� There are error messages from E-01 through E-06� If any of these errors
appear, press the stop button to clear the message� If the error message
reappears please contact your Blendtec Service Agent�
16
7.3 NOISE LEVEL CHANGES
If the blender noise level has increased from original levels, determine whether
the sound is coming from the blender motor or jar�
• Blender motor: Remove the jar, and press Pulse
excessively noisy, please contact your Blendtec Service Agent for evaluation�
• Jar: After checking the motor, fill the jar with 2 cups of water and place back on the
motor base� Run the blender for a few seconds by pressing the Pulse
If you have more than one jar, test a different jar to determine whether the sound
is different� If a jar is excessively noisy, or if the blade assembly seems loose or
sounds gravelly when turned by hand, please contact a Blendtec Service Agent�
7.4 BLENDED TEXTURE UNSATISFACTORY
If the blended texture of product is lumpy or uneven, do the following:
• Ensure the mixture is not cavitating during the cycle� Cavitation is a condition in which
an air pocket forms within the mix because it is too cold or too solid� The blender
blade then spins freely in this cavity� This problem can be corrected by increasing
the mix temperature by either reducing ice, increasing liquid and/or ensuring that the
frozen ingredients used in the recipe are never colder than 10 degrees Fahrenheit
(-12 degrees Celsius)�
• If the recipe is mixing well but has not had enough time for complete blending,
increase cycle time� Try a longer cycle or touch and hold the "Pulse" button for the
required extra blending time�
• TRIED EVERYTHING? If none of the preceding suggestions work, contact your
Blendtec service agent for further assistance�
INSTRUCTIONS THAT APPEAR IN THIS USER GUIDE ARE NOT MEANT TO
COVER EVERY POSSIBLE CONDITION OR SITUATION THAT MAY OCCUR.
GOOD JUDGMENT MUST BE USED WHEN OPERATING THIS OR ANY
OTHER MACHINERY.

SECTION 8: WARRANTY

WARRANTY DESCRIPTION
The motor base and jar assembly, including all moving jar parts, are covered
against leaking or breakage for the warranty period� Warranties begin from date
of purchase�
Cosmetic damage, product abuse, unreasonable use, damage resulting from
an accident (including fire, flood, earthquake or other natural disasters), product
tampering, use of accessories not endorsed by Blendtec, service performed or
attempted by unauthorized service agencies, units that have modifications, or
have been or used for commercial purposes are not included under this warranty�
The quality of Blendtec blenders is unsurpassed� You will enjoy years of wonderful
and reliable service from your Blendtec Designer series Blender�
THIS WARRANTY APPLIES ONLY TO PRODUCTS SOLD BY BLENDTEC OR ITS
AUTHORIZED DEALERS
�Listen to the motor� If it is
button�
17