Tabla de contenido
Idiomas disponibles
Idiomas disponibles
Intended Use
This micro system is intended exclusively for the playback of
audio CDs, MP3-CDs, CD-R, CD-RW, and for the playback of
radio programmes. The micro system is not intended for use
in commercial or industrial environments. No warranty claims
will be granted for damage resulting from improper use!
Items supplied
1 Micro-system
2 Loudspeakers
1 Remote control (Inc. 2 batteries)
1 Operating instruction booklet
Technical data
Rated voltage:
Power consumption:
in Standby:
in Operation:
Frequency range radio:
Measurements (W x H x D):
Main device:
Each speaker:
Weight
Main device:
Each speaker:
Output power.:
AUX - Input
Headphones output:
Max. output voltage
at the headphone socket:
CD Laser:
Operating temperature:
Storage temperature :
Protection class:
Batteries:
Remote control:
Battery backup:
The technical details of the device allow for an adjustable
frequency range of MW (AM) 525-1635 kHz, and/or FM
(USW) 87,2-108,6 MHz. In some countries, different na-
tional regulations may apply to the assigned radio frequency
ranges. Please note that information received outside of the
assigned radio frequency ranges may not be used, passed on
to third parties or otherwise misused.
Safety instructions
•
Do not permit children to handle electrical devices without
supervision, they cannot correctly assess the possible risks
of injury.
•
Unplug the power cord after every use and before cleaning,
so as to prevent the device from switching on inadvertently.
•
Check the device and all parts for visible damages.
The safety concept can work only if the device is in a faultless
condition.
230 V ~ , 50 Hz
3 Watts
14 Watts
AM: 526.5 - 1606.5 kHz
VHF (FM): 87.5 - 108 MHz
25 x 18 x 6,2 cm
11 x 18 x 6,2 cm
1008 g approx.
280 g approx.
2 x 1.2 Watt RMS
3,5 mm Jackplug
3,5 mm Jackplug
60 mV
Laser class 1
5° - 40°C
—20° - 60°C
II
2 x 1,5 V, (AAA, LR03) Micro
2 x 1,5 V, (AA, LR6) Mignon
Risk of explosion!
•
Do not throw batteries into a fire.
•
Do not recharge batteries.
•
Never open batteries, never solder or weld batteries.
The risk of explosions and injuries exists!
•
Regularly check the condition of the batteries.
Leaking batteries can cause damage to the remote control
or to the device.
•
If you do not intend to use the device for an extended pe-
riod, remove the batteries.
•
If the batteries have leaked put on protective gloves and
clean the battery compartment and the battery contacts
with a dry cloth.
Risk of electrical shocks.
•
Connect the device to an electrical wall socket with
a mains voltage of 230 V ~ / 50 Hz.
•
Do not operate the device if the connection cord or the
power plug is damaged.
•
The connection cord or device should be immediately
repaired or exchanged by the customer service
department if they fail to function faultlessly.
•
Never submerse the device in water. Wipe it only with
a slightly damp cloth.
•
Do not expose the device to rain and never use it in
a humid or wet environment.
•
Make sure that the power cord does not become wet
during operation.
•
You must not open the device housing or attempt to repair
the device yourself. There is invisible radiation inside the
device (Class 1 Laser) Furthermore should you do so, the
safety concept of the device may be compromised and the
warranty becomes void.
•
Do not place objects containing fluids, e.g. flower vases,
on or near the device.
•
Notice regarding power disconnection
To completely disconnect the device from mains power,
the plug MUST be removed from the power socket.
For this reason the device should be placed in a position
where unhindered access to the power socket is assured
at all times, so that in an emergency the plug can be quickly
removed. To eliminate the risk of fire you should completely
disconnect the plug from the wall socket if the device is
not going to be used for an extended period, for example,
during holidays.
•
Always take hold of the power cord by the plug. Do not pull
on the cord itself and never touch the power cord with wet
hands, this could result in either a short circuit or you receiving
an electric shock. Do not place the device, furniture or any-
thing else on the power cord and ensure that it does not
become clamped. NEVER tie knots in the power cord and
do not bind it with other cables. Place the power cord in
a position where it cannot be trod on. A damaged power
cord can cause a fire or an electrical shock. Check the
power cord from time to time. Should it become damaged
contact your nearest authorized customer service centre
or dealer to have it replaced.
- 26 -
Capítulos
Tabla de contenido
