Technical Data; Before Starting The Equipment - EINHELL TE-MG 200 CE Manual De Instrucciones Original

4. Technical data

Mains voltage: ............................... 230 V ~ 50 Hz
Power input: .............................................. 200 W
Idling speed: ............................ 15000-21000 rpm
Sanding/grinding area: .............. 90 x 90 x 90 mm
Oscillation angle: ..............................................3°
Protection class: ............................................ II/
Weight: .......................................................1.2 kg
Danger!
Sound and vibration
Sound and vibration values were measured in
accordance with EN 62841.
L sound pressure level ..................... 82,5 dB(A)
pA
K uncertainty ............................................. 3 dB
pA
L sound power level ....................... 93,5 dB(A)
WA
K uncertainty ............................................. 3 dB
WA
Wear ear-muff s.
The impact of noise can cause damage to hea-
ring.
Total vibration values (vector sum of three direc-
tions) determined in accordance with EN 62841.
Handle
Vibration emission value a
K uncertainty = 1.5 m/s
The stated vibration emission levels and stated
noise emission values were measured in ac-
cordance with a set of standardized criteria and
can be used to compare one power tool with
another.
The stated vibration emission levels and stated
noise emission values can also be used to make
an initial assessment of exposure.
Warning:
The vibration and noise emission levels may vary
from the level specifi ed during actual use, depen-
ding on the way in which the power tool is used,
especially the type of workpiece it is used for.
Anl_TE_MG_200_CE_SPK9.indb 17 Anl_TE_MG_200_CE_SPK9.indb 17
= 5.21 m/s
2
h
2
- 17 -
GB
Keep the noise emissions and vibrations to a
minimum.
•
Only use appliances which are in perfect wor-
king order.
•
Service and clean the appliance regularly.
•
Adapt your working style to suit the appliance.
•
Do not overload the appliance.
•
Have the appliance serviced whenever ne-
cessary.
•
Switch the appliance off when it is not in use.
•
Wear protective gloves.
Caution!
Residual risks
Even if you use this electric power tool in
accordance with instructions, certain resi-
dual risks cannot be rules out. The following
hazards may arise in connection with the
equipment's construction and layout:
1. Lung damage if no suitable protective dust
mask is used.
2. Damage to hearing if no suitable ear protec-
tion is used.
3. Health damage caused by hand-arm vib-
rations if the equipment is used over a pro-
longed period or is not properly guided and
maintained.

5. Before starting the equipment

Before you connect the equipment to the mains
supply make sure that the data on the rating plate
are identical to the mains data.
Warning!
Always pull the power plug before making
adjustments to the equipment.
5.1 Fitting the plug-in tools (Figures 1/2/3)
•
To fit the plug-in tools safely you should hold
the multifunction tool so that the ON/OFF
switch (1) points down and the tool mounting
(2) faces up.
•
Place the plug-in tool (e.g. the triangular san-
ding/grinding plant) on the tool mounting (2)
so that the pins of the tool mounting (2) fit into
the recesses in the plug-in tool.
•
Secure the plug-in tool using the supplied
screw (b) and tighten the screw securely with
the Hexagon key (9).
•
Make sure that the washer (a) is used for the
screw (b) only in connection with the saw
blade and the scraper (see Figure 3). In this
case the corrugated face of the washer must
05.09.2019 11:32:09 05.09.2019 11:32:09