Electrical Connection - Air King Barcelona The Segovia Instrucciones De Uso

Dear client:
DECORATIVE EXTRACTOR HOODS
We are sure that the purchase of our range hood will fully
satisfy all of your needs. Please read this instruction manual care-
fully in order to obtain the best results from the use of the hood.
Proof of purchase is required before a warranty claim will be
IMPORTANT
accepted..
Before installing and using the hood, be sure that the voltage (V)
GENERAL INDICATIONS
and the frequency (Hz) indicated on the feature plate match the
voltage and frequency at the installation site.
The feature plate and technical data are shown on the inside of
the product.
This hood is equipped with an adjustable chimney cover which
allows it to be adjusted to the height of the ceiling
• Please, remove the polyfoam protection piece before use.
WALL MOUNTING
• Connect the outlet adapter supplied with the hood (6
inches diameter) to an exhaust duct connected directly to the out-
side.(Fig. 1)
• Screw on the connection box following Fig. 1 with the two
1/8" x 11/16" screws supplied in the box of accessories
• The accessories needed to install the hood are inside the
hood.
• Drill holes in the wall using a 1/4" drill bit.
• The anchors and screws need to hang the hood are contained
in the bag of accessories supplied with the hood.
• This fan shall be mounted a minimum of 22 inches above the
heat source.
Important: Be certain all wiring complies with local codes and the

ELECTRICAL CONNECTION

unit is properly grounded.
• Run three wires, two for the power supply and the ground
wire, from the connection box on the canopy to a power connec-
tion point near the installation. See Fig. 1A.
• Using approved wiring connectors, connect the
power conductors to the conductors for the fan: black to black and
white to white. Connect the grounding wire (green or bare) to the
Ground conductor (green) of the fan distribution box.
ASSEMBLY OF CHIMNEY COVER
• Mark the wall at the location of support E (Figure 2) according
to the heights and specifications shown on the Mounting
Template.
• Drill holes in the wall, place Anchors in the holes and attach
support E with screws.
• Place tube A with the extendible part B hanging on the inside,
making sure that flange D is correctly lodged in the support E
(Fig. 2).
• Next, secure support G to the upper end of the wall, making
sure that it is properly aligned with the extendible tube. Extend the
movable part of tube B until it reaches support G and connect to
the support with the two side screws. (Fig. 5).
FOUR-SPEED CONTROL PANEL WITH DIGITAL
INDICATOR
This panel is situated on the front of the range hood and includes:
- Button for the light (ref. K).
- On/off button of the motor (ref. L).
- Button for reducing the motor speed (ref. M).
- Motor speed indicator (ref. N).
- Button for increasing the motor speed (ref. O).
- Button for directly activating the TURBO speed of the motor
(ref. P).
- Button for setting the timer of the motor (ref. Q).
The hood will operate for 5 minutes at the current speed and
5 minutes at each of the lower speeds until coming to a complete
stop.
IMPORTANT: During an electrostatic discharge (ESD) it is possi-
ble that the device will stop working. By switching the device OFF
an ON the device will again work as intended. There is no risk and
no risk will appear.
MAINTENANCE
• Cleaning: Disconnect the power before cleaning or servicing.
Clean the external part with a mild, liquid detergent and
avoid the use of abrasive cleaning products.
• Changing the light: Before changing the light make sure
that the hood is not operating.
Remove the grease filter and replace the light with a light bulb no
more powerful than that specified in the Technical Characteristics.
Place the filter in position.
IMPORTANT: If the halogen lamps need replacing, they must be
replaced by lamps with an aluminium reflector, never dichroic
lamps, to avoid unnecessary overheating in the lamp holders.
• Cleaning the grease filter: Depending on use, and at least
once a month, the grease filters should be disassembled (Fig. 3)
and (fig. 4) and cleaned in a dishwasher or with hot soapy water.
If washed in a dishwasher they should be placed in an upright
position to prevent food remains from falling on them. After rinsing
and drying, replace the filters by following the steps for disas-
sembly in reverse order.