Care And Maintenance - Aero AeroBed Manual De Instrucciones

INFLATION
Remove your AeroBed ® from its lightweight duffel bag. Keep bag for storage.
Note: Product must be at room temperature prior to inflating.
1. Place your rolled up bed on the floor or other surface free of obstructions or
sharp objects.
2. Make certain the Quick Air Release Valve located at the foot of the bed is closed.
Bed should be stored with valve in the closed and latched position.
If the Air Release Valve is open, close it by using 2 thumbs to push cover and
snap into valve. Be careful to avoid pushing valve cover to the right or left as it
snaps into the valve opening.
This is the closed position. Open Air Release Valve
3. Remove AC plug, cord and One Touch
shrink wrap.
4. Plug into any standard polarized 110 Volt AC electrical outlet.
North American Electrical rating: 120 VAC 60HZ 1.0A
(NOTE: 230VAC product sold outside of North America.)
This product has a polarized attachment plug (one blade is wider than the other)
as a safety feature. This plug will fit into a polarized outlet only one way. If the
plug does not fit fully in the outlet, reverse the plug. If it still does not fit, contact
a qualified electrician. Never use with an extension cord unless the plug can be
fully inserted. Do not attempt to defeat this safety feature.
5. Push and hold the button of the One Touch Comfort
Control for approximately 60 seconds to inflate the
AeroBed to full (firmest) capacity. Bed will not over-inflate.
6. Attach the One Touch Comfort Control block to the
inflator by sliding it over the rubber nipple.
7. Lie on the bed to adjust the firmness to your desired level.
a. To make the bed softer, depress the One Touch
Comfort Control block (not the button) and rubber
nipple together.
b. To make the bed firmer, depress only the button of
the One Touch Comfort Control.
Close Valve Using 2 Thumbs
® Comfort Control from plastic bag and
60 sec
aero
2
DEFLATION AND STORAGE
1. Make sure the bed is unplugged from the electric outlet
prior to deflation.
2. Open the Quick Air Release Valve at the foot of the bed to
release the air.
3. Roll or fold the AC cord with One Touch
block and secure it. Fold sides of bed into the center along
its length. Tightly roll your AeroBed
towards the Air Release Valve end.
4. Roll the bed completely until all air is expelled. When
the Bed is completely rolled, push the Air Release Valve
closed until it locks.
5. Slide the duffel bag over your AeroBed
AeroBed in a clean dry place at room temperature (above
50°F/10° C). Storing your AeroBed under 50° F (10° C) and
over 100° F (38° C) may affect its performance and will
note be covered under warranty.
NOTE: AeroBed must be at room temperature prior to inflating.

CARE AND MAINTENANCE

1. Inspect your AeroBed prior to each use.
2. Keep your AeroBed away from any sharp objects. Large cuts or snags may not
be repairable and will not be covered by your warranty.
3. When not in use, store your AeroBed in its duffle bag, in a clean, dry place out of
extreme temperatures. Product must be at room temperature prior to inflating.
4. Do not store your AeroBed folded inside sofa beds or roll-aways. This may
cause damage to your AeroBed that will not be covered under your warranty.
5. In case of incidental damage to your bed, a repair kit has been included. Please
follow repair instructions carefully.
Inflation
AeroBed ®
You may clean your AeroBed with a mild dishwashing detergent or household
cleaner. Do not use strong chemicals or other compounds. Allow your bed to air dry
completely after cleaning and before storing.
Cover (if included)
The mattress cover is made of polyester/cotton blended fabric. Machine wash in
warm water with a mild soap or detergent. Tumble dry on LOW HEAT.
® Comfort Control
® around the pump
® . Store your
CLEANING
3